Visible light communication (VLC) has emerged as a good accompaniment to radio‐frequency (RF) technologies by deploying multicarrier schemes such as orthogonal frequency division multiplexing (OFDM). However, the coherent summation of carriers in the OFDM system leads to a high peak‐to‐average‐power ratio (PAPR), causing non‐linear clipping distortion at the transmitting light‐emitting diode. This intricacy becomes a potential barrier for intensity modulation and limits the VLC systems' bandwidth. In the literature, non‐distorting PAPR lowering approaches, such as the selective mapping (SLM) approach, have been confirmed as the most effective strategy for reducing ineludible high PAPR in optical OFDM systems among all other available techniques. Besides its astounding performance, the computational complexity also becomes a major complication in SLM due to the generation of multiple candidates. This paper proposes a computational complexity minimisation approach using inherit system properties in the SLM‐based PAPR suppression method for VLC systems, where the phase sequence vectors are considered periodic. The alternative direct current‐biased optical orthogonal frequency division multiplexing candidates for the single frequency‐domain data block are generated with the periodic phase rotation vector. The evaluation of the complexity analysis and the simulation results shows that the mitigation of computational complexity surpasses the standard SLM technique.
Generalized frequency division multiplexing (GFDM) has emerged as a quintessential waveform candidate poised to meet the stringent requirements of next-generation wireless communication frameworks, addressing pivotal 5G physical layer challenges through its flexible, adaptive structure and spectral efficiency. Despite its numerous advantages, GFDM, akin to other multi-carrier schemes, is afflicted by an inherent high peak-to-average power ratio (PAPR), which can degrade power efficiency and impair system performance under high-power amplifier constraints. In this paper, we rigorously derive the complementary cumulative distribution function (CCDF) for GFDM systems, elucidating its intricate dependence on the design and characteristics of pulse-shaping filters, which are instrumental in managing spectral and temporal properties. Furthermore, we introduce an optimized non-linear companding scheme, specifically calibrated to enhance PAPR performance in GFDM systems by tailoring key parameters to achieve a balance between signal integrity and power efficiency. Extensive simulations demonstrate that the proposed approach, in conjunction with refined pulse-shaping filter configurations, yields substantial enhancements in PAPR reduction, outperforming conventional methods within the GFDM framework. To substantiate the theoretical and simulated outcomes, we have developed an experimental testbed leveraging the universal software radio peripheral (USRP) and LabVIEW environment, providing empirical validation and underscoring the real-world applicability of our proposed technique.
Generalized frequency division multiplexing (GFDM) is a flexible block‐structured multi‐carrier scheme recently proposed for next‐generation wireless communication systems. There are various approaches suggested for its analysis and implementation via simulations but testing in real‐time environments is not heavily investigated. This paper carries out the real‐time implementation of the GFDM system utilizing software‐defined radio (SDR) by emphasizing mainly channel estimation and synchronization. Symbol timing, frequency offset, and channel estimate algorithms are applied using a windowed preamble with two identical halves to satisfy low egress noise requirements. Time and frequency estimation is evaluated in terms of residual offsets along with symbol error rate over frequency selective channels. This algorithm is extended to a preamble composed of multiple identical parts. This facilitates a large frequency estimation range at the cost of complexity. For practical validation of the above concepts, the National Instruments (NI) universal software radio peripheral (USRP) 2953R is employed as hardware and it is interfaced with LabVIEW.
The remarkable attributes like elevated transmission rates, low latency, minimal out band emission and enhanced spectral efficiency of the generalized frequency division multiplexing (GFDM) system have lured the significant attention from research community. However, the inherent superposition of multiple symbols within the time domain results in a notable amount of peak-to-average power ratio (PAPR) that affects the performance due to non-linear front end circuitry. The selected mapping (SLM) technique resolves this problem by employing phase rotation vectors to generate alternative signal representations. Conventionally, phase sequence vectors possess uniform magnitudes, thereby constraining the achievable PAPR reduction. To address this limitation, we propose the use of normalized rows from the Riemann matrix as phase sequence vectors, given their inclusion of components with substantial magnitudes. This approach mitigates excessive peaks and consequently yields superior PAPR reduction gains. To optimize real-time system performance, side information (SI) is also integrated into the transmitted signals alongside the normalized Riemann matrix sequences. Indeed, for validation purpose, an experimental setup utilizing the universal software radio peripheral (USRP) 2953R in conjunction with LabVIEW software is employed for real-time transmission. The observed spectral response from the USRP closely aligned with simulation results, affirming the efficacy of the proposed method.