28 February 2018 in Fibres & Textiles in Eastern Europe
The purpose of this study was to examine the effect of spinning technologies and weave design on fabric mechanical and surface properties. For this purpose, ring spun (combed, carded) and open-end (OE) techniques were used to manufacture yarns of polyester cotton (50:50) which were used in the weft, and 100% cotton yarn in the warp. Plain, twill, and satin weave designs were selected to construct woven samples on a projectile loom. The variation in fabric tensile strength is obvious with respect to weave designs. Higher interlacing of yarn produces more crimp in the load bearing, which may cause lower breaking strength and fewer broad floats. The mechanical and surface properties of these fabric samples were investigated and statistical analysis was performed, which showed a significant effect of the spinning technique and weave design on these properties.
23 December 2019 in The Journal of the Textile Institute
Development of heating fabrics has a great potential in numerous applications. Heating fabrics can be developed by various approaches each having its own strengths and weaknesses. Incorporating staple fibre spun conductive yarn in the development of lightweight heating pads offers the advantage of obtaining required heating effect while maintaining flexibility, durability and comfort of the developed fabric. This study aimed at developing a conductive hybrid spun yarn composed of polyester and stainless staple fibers and characterizing its thermal behaviour in response to changes in its structural and procedural parameters. The effect of three variables namely yarn twist coefficient, applied voltage and tension on the yarn during testing, was investigated on thermal behavior of the yarn. Among the three, the applied voltage was found to dominantly control the temperature and hence the heating effect of the hybrid yarn. Yarn twist coefficient, which makes the yarn structure of the same fineness more compact at higher twist levels, was found to improve the heating effect at increased twist level at an applied voltage. However, changes in the tension on the yarn during the test was found to be not affecting the yarn temperature, thus producing a steady heating effect under varying tensions. The study shows that other than changing the applied voltage, the heating effect of the yarn can be improved by changing its twist level which controls the compactness of the yarn and thus different products with required thermal behavior can be tailored.
7 August 2017 in The Journal of the Textile Institute
High strength fabrics are perfect materials for use in automotive and aerospace systems, where high performance and light weight structures are demanded. Mechanical characterization under constant loading is of great importance for these materials. The purpose of this study is to analyze the tensile properties of Basalt and Glass-woven structures at different pick density, weave design, stitch distance, and number of layers. For this purpose, single and double layerwoven fabric structures have been prepared using Basalt and Glass yarns on sample weaving loom. Their uniaxial testing has been performed to analyze their tensile curves. Analysis of variance showed the statistical significance of material, pick density, direction of applied load, weave, and stitching in strength of fabric, while the effect of stitch distance was insignificant.
1 September 2020 in Autex Research Journal
Woven compression bandage (CB) is one of the elastic textiles that exert pressure on muscles. With a defined tensile strength, it is possible to create the required compression on the given body parts. This work aims to investigate the relationship between woven fabric deformation, porosity, and tensile stress properties of three main types of woven CBs. All bandage samples are applied on human leg using two- and three-layer bandaging techniques. Bandage porosity is calculated for all frames at different weave angles using NIS software. Woven bandage construction parameters which are given by the preparation of warp and weft yarns, twist, count, and density along with woven fabric weave, type of weaving, and finishing process are the main factors that influence the bandage properties. Several methods considering thread distributions have been developed to determine the woven fabric's porosity during the tensile stress. Experimental results confirm that bandage porosity is directly proportional to the bandage extension and weave angle that ranges from 44° to 90°. The novelty of candidate study is to introduce practical remarks to the patient for optimizing the required bandage pressure by suitable extension or applied tension or weave angle for two- and three-layer bandaging systems.
1 July 2018 in Industria Textila
This experimental work investigates the effect of yarn structure on cover factor of fabrics at different weft settings by the light transmission method. To analyze the effect, two different types of fabric set have been prepared by using airjet and rotor yarns of the same linear densities in the weft direction and keeping the warp yarn unchanged. For each fabric, weft setting has been changed gradually. Cross-sectional diameter of yarn and its packing density has been analyzed to find out the differences between both yarn structures. The effective yarn diameter and packing density have been found to be almost same for both yarns while the hairiness is found to be higher in airjet yarn as compared to rotor yarn. Yarn cross-section in the fabric has also been analyzed to examine the deformation (flatness) in yarn, which was relatively higher in airjet yarns. At the same weft setting the cover factor (CF) of fabric woven by air jet yarn is found to be higher than fabric woven by rotor jet yarn, and this difference decreases as the weft setting increases in fabric. Correlation analysis results show the relation between the cover factor and weft setting. While analysis of variance results show statistically significant effect of spinning system (airjet and rotor yarn) and weft setting on the cover factor of woven fabric.
25 May 2019 in The Journal of the Textile Institute
The theoretical model for description of mutual interlacing of threads in multifilament woven fabric structure using Fourier series derived from plain woven structure has been validated in this work with experimental results. The internal geometry of the woven fabrics and the deformation in the single and two layer woven structures has been evaluated by the cross-sectional image analysis method. The approximation using the linear function in Fourier series along longitudinal and transverse cross-section has been performed for single layer and two layer stitched woven fabrics, which fits well to the experimental binding wave. The spectral characteristics of binding waves obtained by Fourier series (theoretical) has been compared with the experimental values, which are very close to each other in longitudinal and transverse cross-section. By evaluating the geometrical parameters of yarn in the real cross-section of a woven fabric, it is possible to compare it with the theoretical shape of a binding wave by analyzing its individual coordinates.