20 December 2022 in IEEE Journal of Microwaves
This paper reviews the latest developments in microwave acoustic wave devices. After an introduction and brief history of bulk acoustic wave (BAW) and surface acoustic wave (SAW) devices, a review is given for guided SAWs and XBARs - two new technologies, which are promising for future 5G applications. Following this, we discuss recent simulation techniques, such as 3D finite element method (3D FEM) and simulation of nonlinearities, as well as filter synthesis. Next, a review on tunable and reconfigurable acoustics is given. Finally, we present the latest developments in microwave acoustics for millimeter-wave (mm-wave) operation as well as BAW oscillators.
1 January 2019 in Electronics Letters
In a free‐standing 400‐nm‐thick platelet of crystalline ZY‐LiNbO 3 , narrow electrodes (500 nm) placed periodically with a pitch of a few microns can eXcite standing shear‐wave bulk acoustic resonances (XBARs), by utilising lateral electric fields oriented parallel to the crystalline Y ‐axis and parallel to the plane of the platelet. The resonance frequency of ∼4800 MHz is determined mainly by the platelet thickness and only weakly depends on the electrode width and the pitch. Simulations show quality‐factors ( Q ) at resonance and anti‐resonance higher than 1000. Measurements of the first fabricated devices show a resonance Q ‐factor ∼300, strong piezoelectric coupling ∼25%, (indicated by the large Resonance‐antiResonance frequency spacing, ∼11%) and an impedance at resonance of a few ohms. The static capacitance of the devices, corresponds to the imaginary part of the impedance ∼100 Ω. This device opens the possibility for the development of low‐loss, wide band, RF filters in the 3–6 GHz range for 4th and 5th generation (4G/5G) mobile phones. XBARs can be produced using standard optical photolithography and MEMS processes. The 3rd, 5th, 7th, and 9th harmonics were observed, up to 38 GHz, and are also promising for high frequency filter design.
15 June 2023 in Journal of Microelectromechanical Systems
This work presents the study of suspended Y-cut Lithium Niobate shear bulk acoustic resonators for wide band filter applications in the frequency range of 3.5-4.5GHz. The resonators consist of a Lithium Niobate film with Aluminum top interdigitated electrodes (IDE) and floating bottom metal plate. Through vertical electric field excitation, shear bulk acoustic waves are generated in each unit cell of the device functioning as a quasi-independent resonator. Measured devices at 3.7GHz having large relative resonance-antiresonance bandwidth of 16.7% (750MHz), with 2 $\mathrm{\Omega }$ impedance at resonance are presented. Suppression of higher order lateral harmonics through etching of trenches in the Lithium Niobate and geometric optimization is discussed.2022-0205
26 July 2021 in Electronics Letters
The recently invented laterally excited bulk wave resonators (XBARs) demonstrate outstanding parameters suitable for the design of low loss filters for the fifth generation of mobile phones. The operation of XBARs can be interpreted as an excitation of anti‐symmetric Lamb mode A1 by the interdigital transducer. However, it can also be seen as the generation of fundamental plate resonances in a set of parallelly connected quasi‐independent resonators, excited by a lateral electric field created by narrow electrodes with alternating polarity. By exploiting this latter interpretation, we propose a formula for the admittance of multi‐layered membranes, including the main piezoelectric layer of suitable orientation and different additional dielectric layers on both sides of the membranes. The structure can be asymmetric and the excitation of all shear wave thickness resonances, not only with odd numbers, is described. The formula can be used for the one‐dimensional modelling and optimisation of XBARs and the estimation of the resonance frequency dependence on the deposited trimming thin layers.