25 October 2011 in RSC Advances
In the past few years a novel concept of Solid Oxide Fuel Cells (SOFC) has been developed: the symmetrical Solid Oxide Fuel Cells (SSOFC). In this configuration, the same electrode material is used as anode and cathode. Several state-of-the-art SOFC electrode materials have been tested and optimised to operate in such a novel configuration, as is the case of the lanthanum chromites traditionally used as interconnect materials, lanthanum chromium manganites and strontium titanates generally used as anodes and lanthanum manganites typically used as cathodes. Fuel cell performances of approximately 800 mW cm−2 and ∼500 mW cm−2 under H2 and CH4 atmospheres have been obtained using some of these materials in symmetric configuration. Moreover, promising performances have also been reported for interconnect-based materials under city gas containing the impurity H2S. An interesting feature of the compositions evaluated is their potential use as symmetrical electrodes for Solid Oxide Electrolysis Cells (SOEC) with efficiencies in the range of the conventional SOEC systems, i.e. LSM-YSZ/YSZ/Ni-YSZ. Hence, they may be considered all-in-one Symmetric and Reversible SOFCs (SR-SOFCs) with significant advantages compared to traditional configurations, regarding both fabrication and maintenance/operation. In this review, we provide an insight into the most common materials tested as symmetrical electrodes for SOFCs and SOECs, electrolytes employed, configurations tested, new fabrication processes and procedures for microstructural engineering.
13 October 2010 in Energy & Environmental Science
The search for cleaner environmentally friendly power sources has been one of the hot topics in research over the past few years. Solid oxide fuel cells can be considered a promising option for the production of clean energy and one of the simplest routes to improve the efficiency of these devices is the microstructural engineering of component materials. In this work, an insight is provided into several cost-effective procedures of microstructural control of SOFC materials, ranging from an “eye-scale” down to the micrometre scale. The proposed procedures may be considered general and as such they can be used to optimise various materials for energy and environmentally related areas.
16 September 2013 in RSC Advances
We have explored the emerging and ground-breaking photonics approach to enhance the photocatalytic activity of one of the main semiconductor electrodes used in water-splitting reactions, titanium dioxide (TiO2): the blue shifting of the incident radiation by means of a highly efficient up-conversion by a rare-earth (RE) doped luminescent material to assist in the harvesting of long wavelengths in unused portions of infrared light. We present an up to 20% improvement of the photocatalytic action of the commercial benchmark TiO2 efficient photocatalyst in the decomposition of methylene blue in water under Xe-lamp irradiation, and also an outstanding enhancement by a factor of about 2.5 of the photolytic degradation rate of this pollutant. Our results prove that the ultraviolet (UV) radiation that reaches the TiO2 particles is increased by the addition of the RE-doped powder material into a slurry-type photo-reactor, boosting both the photocatalytic and photolytic degradation rates. Thus, we show the feasibility of handling and transforming the incoming infrared radiation, bridging the UV gap of the photocatalytic semiconductor. Let us turn the infrared into the blue; there is plenty of energy at the bottom.
25 September 2008 in Journal of Materials Chemistry
XRD, XPS and electrochemical studies show clear evidence of chemical interaction under oxidising and reducing conditions between YSZ and CuO, both components of a widely studied anode material for high performance solid oxide fuel cells (SOFCs). The aim of this work is to identify and verify the nature of this interaction and find means to prevent its formation during the fabrication process of a fuel cell.
5 January 2009 in Journal of the American Ceramic Society
A novel, simple, and cost‐effective method allows material engineering for the creation of a 2D/3D matrix of cross‐linked channels through whole solid oxide fuel cell (SOFC) electrode materials. The size of the channels can be precisely tailored from a few micrometers up to 75–90 μm and remains stable up to 1500°C. Because of the versatility of the method proposed, it can be applied to practically any type of material commonly used in SOFC technology or in other fields.