9 January 2023 in IEEE Transactions on Instrumentation and Measurement
In this paper, an analytical expression (model) for the capacitance of coplanar interdigitated (IDT) capacitive sensors of four 1-n-1 patterns (such as 1-1-1, 1-3-1, 1-5-1 and 1-11-1), based on conformal mapping techniques have been obtained. An important feature of the proposed model is that it is universal and independent of any specific application. The proposed model can be used for any number of layers (variable permittivity & thickness), finger width, and the gap between the fingers. In general, the capacitance of a particular IDT sensor depends on finger (electrode) length, the number of fingers, potential distribution of the fingers, dielectric permittivity (substrate and sensitive layers), and geometric parameters (non-dimensional): (i) the ratio between the finger widths and gap; (ii) the ratio between the top sensitive layer thickness and the sensor wavelength (spatial). Keeping these parameters in mind, comparisons with finite element analysis and experimental results have been made. Also, to confirm the effectiveness of the proposed model, different patterns of 1-n-1 structured IDT sensors have been developed to measure the water droplets on the leaf canopy by a non-contact method. The proposed sensor structure can be said to be a non-contact leaf wetness sensor (LWS), generally employed to quantify the leaf wetness duration (LWD).
1 October 2022 in International Journal of Electrical and Computer Engineering (IJECE)
Parameters evaluation, design, and intelligent control of the solar photovoltaic model are presented in this work. The parameters of zeta converters such as a rating of an inductor, capacitor, and switches for a particular load are evaluated its values to compare the trade of the existing model and promoted to research in the proposed area. The zeta converter is pulsed through intelligent controller-based maximum power point tracking (intelligent-MPPT). The intelligent controller is a fuzzy logic controller (FLC) which extracts maximum power from the solar panel using the zeta converter. The performance of evaluated parameters based on the solar system and zeta converter is seen by an intelligent control algorithm. Moreover, evaluated parameters of solar photovoltaic (PV) and zeta converter can be examined the performance of fuzzy based intelligent MPPT under transient and steady-state conditions with different solar insolation. The brushless direct current motor-based water pump is used as the direct control (DC) load of the proposed model. The proposed model can enhance the research and assist to develop a new configuration of the present system.
7 December 2024 in Solar Energy and Sustainable Development journal
This article addresses the critical challenge of optimizing solar array performance for electrolysis-based green hydrogen generation. A fuzzy logic controller (FLC) for maximum power point tracking (MPPT) was proposed in this study to maximize the performance of solar arrays in electrolysis-based hydrogen generation. The FLC does away with the need for traditional methods like Perturb and Observe (P&O) by dynamically adjusting the DC-DC converter duty cycle based on real-time temperature and irradiance inputs. Under various climatic conditions, MATLAB/Simulink simulations show a 92% operational efficiency and a 25% increase in hydrogen output, surpassing P&O (78%) and Incremental Conductance (82%). The FLC is a reliable option for scaling renewable energy systems because of its versatility and inexpensive computational cost.
28 July 2025 in Environmental Technology & Innovation
3 April 2026 in Science and Technology for Energy Transition
This work minimizes the issue of traditional Air Conditioners (AC) by employing an innovative design for DC AC and optimizing energy resources, developing an adaptive Feedforward Incremental Conductance (FFINC) algorithm, and conducting experimental validation and cost-benefit analysis. The proposed AC can regulate the moisture levels in a room using an innovative structure that circulates pleasant air indoors. This innovative design represents a potential replacement for traditional AC. The authors have developed a solar air cooler suitable for the modern era that can either replace AC units under specific conditions or reduce their number when operating in hybrid mode. This design sets the distance between the water circulation area and the DC fan at 3 cm to ensure efficient air cooling. The system includes a 60 W DC fan that draws cool air containing water, which passes through a water absorber filter. This filter absorbs excess moisture, resulting in dry, cool air that takes a 90 ° circular path to minimize remaining moisture, thereby enhancing air quality. A 20W DC water pump and the DC fan use energy from various electrical sources. Under sunny conditions, a solar panel, connected via a DC to DC zeta converter, provides power to the DC air cooler. During cloudy weather or nighttime, an AC to DC converter is used to optimize operation in emergency situations; a battery is available to ensure uninterrupted operation.