1 January 2004 in Journal of Crystal Growth
16 March 2004 in Applied Physics Letters
The effect of gate oxidation method on the electrical properties of metal-oxide-semiconductor field-effect transistors (MOSFETs) fabricated on 4H-SiC face has been investigated. In the case of SiC MOSFETs fabricated by dry gate oxidation, the peak value of field-effect mobility is 16.3 On the other hand, pyrogenic gate oxidation and pyrogenic gate oxidation followed by postoxidation annealing (POA) considerably decreased the interface trap density and the threshold voltage, and markedly improved the The depth profiles of hydrogen density were measured using secondary ion mass spectroscopy. These verified that pyrogenic gate oxidation increases hydrogen density at the interface compared to dry gate oxidation, and that the pyrogenic gate oxidation followed by POA increases considerably it. It is thought that the reduction might be caused by the passivation of interface states by –H or –OH. The peak value of for SiC MOSFETs fabricated by pyrogenic gate oxidation followed by POA is 111 which is much higher than that of SiC MOSFETs fabricated on a Si(0001) face. Therefore, the 4H-SiC face is suitable for the fabrication of SiC power MOSFETs.
23 August 2004 in Applied Physics Letters
Anisotropy of the impact ionization coefficients of silicon carbide is investigated by means of the avalanche breakdown behavior of diodes on (0001) and silicon carbide epitaxial wafers. The impact ionization coefficients are extracted from the avalanche breakdown voltages and the multiplication of a reverse leakage current, due to impact ionization of these diodes. The breakdown voltage of a diode on a wafer is 60% of that on a (0001) wafer, and the extracted impact ionization coefficients of silicon carbide show large anisotropy. We have shown that the anisotropy of the impact ionization coefficients is related to the anisotropy of carrier heating and drift velocity, which are due to the highly anisotropic electronic structure of silicon carbide.
1 October 2004 in Journal of Crystal Growth
7 August 2002 in IEEE Electron Device Letters
Effects of hydrogen postoxidation annealing (H/sub 2/ POA) on 4H-silicon carbide (SiC) MOSFETs with wet gate oxide on the (112~0) face have been investigated. As a result, an inversion channel mobility of 110 cm/sup 2//Vs was successfully achieved using H/sub 2/ POA at 800/spl deg/C for 30 min. H/sub 2/ POA reduces the interface trap density by about one order of magnitude compared with that without H/sub 2/ POA, resulting in considerable improvement of the inversion channel mobility to 3.5 times higher than that without H/sub 2/ POA. In addition, 4H-SiC MOSFET with H/sub 2/ POA has a lower threshold voltage of 3.1 V and a wide gate voltage operation range in which the inversion channel mobility is more than 100 cm/sup 2//Vs.
1 September 2004 in Journal of Applied Physics
The temperature-dependent hole concentration p(T) and hole mobility μp(T) are obtained in p-type 4H-SiC epilayers with several Al-doping densities. From p(T), the densities and energy levels of acceptors are determined by the graphical peak analysis method (free carrier concentration spectroscopy: FCCS) without any assumptions regarding the acceptor species. In the heavily Al-doped case, the excited states of acceptors affect p(T) because the Fermi level is located between the valence band maximum and the acceptor level (i.e., the ground state level of the acceptor), indicating that a distribution function for acceptors, which includes the influence of excited states of acceptors, should be required. Here, FCCS can determine acceptor densities and acceptor levels using any distribution function (e.g., the Fermi-Dirac distributing function or the distribution function including the influence of excited states). Two types of acceptor species are detected in the lightly Al-doped epilayers, while only one type of acceptor species is found in the heavily Al-doped epilayer. Some of the parameters required to simulate electric characteristics of 4H-SiC power electronic devices are obtained; (1) the dependence of each acceptor level on a total acceptor density and (2) the dependence of the hole mobility on temperature and total impurity density.