George A. Jackson

George A. Jackson

Auto-generated profile, based on publicly available information

George A. Jackson

University of Nottingham

Research Focus & Metrics

Academic Career Length

35Years (1992-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2016 in Surface and Coatings Technology
Verified
Journal Article
Closed access
HCHao Chen
Hao Chen
GJG.A. Jackson
G.A. Jackson
KVK.T. Voisey
K.T. Voisey
DMD.G. McCartney
D.G. McCartney

1 January 1992
Verified
Book Chapter
Closed access
PDF file
RJRichard A. Jahnke
Richard A. Jahnke
GJGeorge A. Jackson
George A. Jackson

5 July 2017 in Journal of Thermal Spray Technology
Verified
Journal Article
Closed access
PDF file
HCHao Chen
Hao Chen
GJG. A. Jackson
G. A. Jackson
WSW. Sun
W. Sun

1 April 2017 in Key Engineering Materials
Verified
Journal Article
Closed access
PDF file
GJG.A. Jackson
G.A. Jackson
WSWei Sun
Wei Sun
DMD. Graham McCartney
D. Graham McCartney
Thermally sprayed MCrAlY bond coats are important elements of thermal barrier coating (TBC) systems which are applied to the surface of gas turbine components to protect them in high temperature environments. Knowledge of their mechanical properties is essential in preventing TBC failure which can have catastrophic consequences. However, limited data on modulus, strength and ductility are available for such coatings. In this work, the ductile to brittle transition behaviour of a CoNiCrAlY coating has been investigated via the small punch tensile test (SPTT). Displacement controlled tests were carried out on free standing coatings at room temperature (RT) and between 400-750 °C at a rate of 1 μms-1. At low temperatures there was evidence of elastic-brittle behaviour and at high temperatures there was clear evidence of yielding and plastic deformation. The ductile to brittle transition temperature was found to be between 500-750 °C. The yield stress ranged from 1000-1500 MPa below 600 °C to less than 500 MPa above 650 °C. The elastic modulus was found to be approximately 200-230 GPa at 500 °C and 55 GPa above 700 °C. At room temperature the fracture surface showed flat, smooth features indicating brittle failure whereas at 700 °C there was evidence of ductile tearing.

1 April 2017 in Key Engineering Materials
Verified
Journal Article
Closed access
PDF file
GJG.A. Jackson
G.A. Jackson
HCHao Chen
Hao Chen
WSWei Sun
Wei Sun
DMD. Graham McCartney
D. Graham McCartney
Thermal barrier coatings (TBC’s) protect superalloy components from excessively high temperatures in gas turbines. TBC’s comprise of a ceramic top coat, a metallic bond coat and a thermally grown oxide (TGO). The creep behaviour of the MCrAlY bond coat, which is sensitive to the composition and the method of deposition, has a significant effect on the life of the TBC. High velocity oxy-fuel (HVOF) thermal spraying is a popular deposition method for MCrAlY bond coats however the creep properties of HVOF MCrAlY coatings are not well documented. The creep behaviour of a HVOF thermally sprayed CoNiCrAlY coating has been determined by small punch creep (SPC) testing. Tests were conducted between an equivalent uniaxial stress range of 37-80 MPa at 750 °C on two different SPC rigs and between 30-49 MPa at 850 °C on a single SPC rig. The measured steady-state creep deformation rates at 750 °C were consistent across the two rigs. A comparison with previous work demonstrated that the creep behaviour of HVOF CoNiCrAlY coatings is not sensitive to the manufacturing variability associated with HVOF thermal spraying. The CoNiCrAlY coating exhibited typical SPC deformation at 750 °C. At 850 °C the CoNiCrAlY coating showed significantly different creep behaviour which could be attributed to the onset of superplasticity.