2 March 2020 in Journal of Applied Physics
Caloric materials exhibit significant entropy variations when applying appropriate excitation, pushing forward the development of solid-state cooling systems. Their development includes materials' properties optimization, with a focus on their adiabatic temperature change when driven at their limit. In order to sustain the device development, an analytical model for regenerative cooling systems is presented in this work. It consists of a caloric material driven cyclically so that it exhibits harmonic temperature variations, whereas an oscillating fluid layer is exchanging heat with the caloric material, leading to a net heat flux along one given direction. The heat transfer equation was solved analytically for harmonic excitations along the direction perpendicular to caloric material layers separated by fluid layers. In the second step, the problem was solved along an axis parallel to the layers. In order to validate the model, an experimental proof of concept was developed based on a natural rubber tube inside which water flows harmonically. The comparison between the model and experiment is given, while the model highlights the importance of the thermal boundary layer and how the geometry of the device easily compensates for the low thermal conductivity of natural rubber.
9 November 2020 in Applied Physics Letters
Very few studies have explored the elastocaloric effect of elastomers other than natural rubber (NR). The aim of the present article is thus to evaluate the elastocaloric properties of a thermoplastic polyurethane (TPU) in terms of microstructural characteristics and thermoelastic coupling. Calorimetric measurements showed two successive peaks at 240 K and 282 K, attributed to the crystallization and melting of soft segments, respectively. X-ray diffraction indicated that TPU exhibited a fully reversible strain-induced crystallization at room temperature. Thermomechanical experiments performed at different elongations revealed a minimum adiabatic temperature variation of about −8 K after retraction of a sample initially elongated at λ = 5. This is comparable to NR performances. However, for cycles carried out between λ = 1 and λ = 5, tensile stress/elongation curves showed a non-elastic behavior of TPU. A pseudo-elastic response was obtained for cyclic elongation when unloading was incomplete, in our case, when λ was between 3 and 5. The recorded peak-to-peak temperature variation decreased from 4.5 K to 3.3 K when the number of cycles was increased to 5000. Despite the fact that the issue of fatigue resistance for TPU needs to be addressed, this work opens new perspectives for studying the elastocaloric properties of various polyurethanes (whether crosslinked or thermoplastic) as well as other materials with a tendency for strain-induced crystallization, such as polychloroprene, hydrogenated acrylonitrile butadiene rubber, and others.
10 November 2022 in Polymer
19 July 2022 in Inorganic Chemistry Communications
1 January 2004 in Ferroelectrics
Recently, it has been shown that co-doping with 1% mol. Manganese and 1% mol. fluorine a PZT base composition improved the dielectric and piezoelectric properties. A model based upon electron transfers between Mnα + ions (α = 2, 3, 4) has been proposed to explain such a behaviour. F co-doping has been realized on Cr and Sn doped PZT to determine if the same model is valid with other acceptor dopants possibly exhibiting different valency states in the PZT. (Sb, F) and (Nb, F) co-doped PZTs were also studied to estimate the influence of fluorine on the valency state of donor dopants. XRD measurements revealed that F co-doping generates lead vacancies in the cationic sublattice of Cr doped PZT instead of partially reducing cationic dopant. No change is observed in the unit cell volume and the piezoelectric properties of Sb and Nb doped PZTs after F co-doping. In the case of Sn doping, F− ion may make Sn 2+ and Sn 4+ coexist in the PZT but the characteristics are not as high as (Mn, F) co-doped PZT ones. The correlation between cubic unit cell volume and lead vacancies content in the PZTs was supported by flame Atomic Absorption measurements. The study confirms that the softening effect observed is not due to the increase of extrinsic lead vacancies content but to the coexistence of three valency states of the cationic dopant like Mn+ 4, + 3, + 2 .