Low efficiency of conventional fertilizer (quick release fertilizer) application in agricultural sectors has caused environmental pollution and health problems. A method to overcome the drawback of the conventional fertilizer is by controlled release fertilizer (CRF) preparation. CRF is expected to be able to fulfil the nutrient demand of targeted plants. The objective of this research is to prepare CRF by coating NPK fertilizer with multilayer chitosan-polyanion using alginate, pectin, and sodium tripolyphosphate (TPP). In addition, the effect of the layer arrangement modification of material on the rate of nitrogen release was also studied. The mechanical strength of coated fertilizer was analysed by compressive stress test and the properties of the fertilizer coating was observed by scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR). The nitrogen release study shows that multilayer of chitosan-alginate (CA)5, chitosan-pectin (CP)5, and chitosan-TPP (CT)5 as coating material was able to increase the compressive stress and decrease the nitrogen release of coated fertilizer. These results are supported by the FTIR analysis which exhibits the formation of ionic interaction between amine group of chitosan and carboxyl group of alginate in chitosan-alginate (CA)5 layer, carboxyl group of pectin in chitosan-pectin (CP)5 layer, and phosphate of TPP in chitosan-TPP (CT)5 layer. On the other hand, the modification of the arrangement of chitosan-alginate layers showed that the fertilizer with the alternating layer arrangement (CA)5 was able to optimally increase the compressive strength. The mathematical model for the nitrogen release of coated fertilizer is also prepared and simulated with the MATLAB software. The simulation results showed that the nitrogen release of coated fertilizer followed the proposed diffusion mechanism. The obtained diffusivity coefficient value in the layer of chitosan-alginate (CA)5 is 2.0933 × 10−6 cm2/s, 2.5606 × 10−6 cm2/s in chitosan-TPP (CT)5 layer, and 3.7256 × 10−6 cm2/s in chitosan-pectin (CP)5 layer.
Kulit durian merupakan biomassa yang mempunyai potensial sebagai sumber pektin. Salah satu pemanfaatan pektin adalah digunakan dalam pembuatan edible film yang merupakan lapisan tipis dan memiliki fungsi sebagai pengemas atau pelapis makanan, sertadapat dimakan sekaligus dengan produk yang dikemasnya. Untuk memanfaatkan kulit durian tersebut dalam penelitian ini dibuat edible film dengan bahan pati singkong, gliserol dan pektin kulit durian. Pengaruh konsentrasi pektin dan pengaruh konsentrasi gliserol terhadap karakteristik edible film yang dihasilkan akan dikaji dengan melihat ketebalan, uji kuat tarik, persen elongasi, dan daya serap air nya. Hasil menunjukkan bahwa pada variasi perbandingan massa pektin diperoleh bahwa peningkatan konsentrasi pektin dapat menambah kuat tarik dan elongasi edible film, namun peningkatan konsentrasi pektin tersebut tidak berpengaruh signifikan terhadap ketebalan dan daya serap edible film. Adapun pada variasi perbandingan massa gliserol diperoleh bahwa peningkatan konsentrasi gliserol dapat meningkatkan persen elongasi, kuat tarik, dan daya serap air edible film. Namun penambahan gliserol yang berlebih akan mengurangi nilai kuat tarik dan daya serap air edible film. Pada variasi penambahan pektin didapatkan hasil karakteristik yang terbaik adalah pada perbandingan massa pati:gliserol:pektin 3:1:1,25 dengan nilai ketebalan edible film sebesar 0,112 mm, nilai kuat tarik sebesar 9,32 N, dan nilai persen elongasi sebesar 79,59%.
The application of conventional fertilizer, especially for inorganic fertilizer, has low efficiency due to the fast release of its nutrients into the environment. Also, it has a high operating cost caused by multiple fertilization processes in one of the planting periods. One of the possibilities to overcome this limitation is applying organic fertilizer as a slow-release fertilizer (SRF). The objective of this research is to prepare SRF by modifying the formulation of local organic fertilizer with chitosan as a binder. The rate of the nitrogen release was studied and simulated with MATLAB. The result shows that the nitrogen loss by water leaching decreased up to 85% in chitosan/organic fertilizer rather than the fertilizer without chitosan. By MATLAB simulation, the release of nitrogen has followed the proposed mathematical model in which the mass transfer occurred dominated by diffusion mechanism with the diffusivity coefficient of 1.61x10-5 cm2/s.Keywords: chitosan; organic fertilizer; slow-release fertilizer A B S T R A KPenggunaan pupuk anorganik masih memiliki efisiensi rendah yang disebabkan oleh cepatnya pelepasan nutrisi pupuk ke lingkungan sehingga nutrisi tersebut tidak dapat terserap baik oleh tanaman. Selain itu, aplikasi pupuk anorganik yang berulang dalam satu periode tanam berdampak pada peningkatan biaya operasional. Salah satu metode untuk mengatasi permasalahan tersebut adalah dengan menggunakan pupuk lepas lambat (slow-release fertilizer) atau dengan menggunakan pupuk organik. Tujuan pada penelitian ini adalah dengan mengombinasikan dua metode tersebut yaitu dengan memodifikasi formulasi dari pupuk organik lokal dengan penambahan kitosan sehingga dapat diperoleh pupuk organik yang memiliki sifat lepas lambat. Laju pelepasan nitrogen dari pupuk yang dihasilkan kemudian dianalisis dan disimulasikan dengan software MATLAB. Hasil penelitian menunjukkan bahwa nitrogen yang hilang pada komposit pupuk organik-kitosan melalui water leaching menurun hingga 85% jika dibandingkan dengan komposit pupuk organik tanpa kitosan. Hasil simulasi MATLAB juga menunjukkan bahwa laju pelepasan nitrogen pada pupuk mengikuti model matematika yang diusulkan yaitu dengan mekanisme difusi, nilai koefisien difusivitas yang diperoleh adalah sebesar 1,61×10-5 cm2/s.Kata kunci: kitosan; pupuk lepas lambat; pupuk organik
The biodegradable film is an attempt to reduce the use of plastics that cannot be decomposed by nature. This study described biodegradable films produced from arrowroot starch using the casting method. As a plasticizer and crosslinker, glycerol and citric acid are added. The investigation results indicate that the biodegradable film has a clear white color; the greater the amount of starch, the more opaque the color. The tensile strength test results also indicate that the biodegradable film’s tensile strength will be greater the more starch is used, but its percent elongation at break will decrease, or its characteristics will become less elastic. In contrast, adding citric acid demonstrates that the tensile strength decreases due to the hydrolysis of glycosidic linkages in starch.
Adsorben berupa pektin berhasil diekstraksi dari kulit pisang menggunakan larutan asam kuat dan telah digunakan untuk menyisihkan ion Fe3+ dalam air. Pengaruh berbagai parameter terhadap proses adsorbsi, seperti waktu kontak, pH larutan, dosis adsorben, dan temperatur adsorbsi diinvestigasi dalam suatu sistem batch. Konsentrasi ion Fe3+ dalam larutan air diukur menggunakan Atomic Absorption Spectrometry . Efisiensi adsorbsi terbaik diperoleh pada waktu kontak selama 4 jam, pH larutan 2, dosis adsorben sebesar 3 g, dan temperatur 20oC. Mekanisme proses adsorbsi dan perubahan energi bebas Gibbs, entalpi, serta entropi telah dievalusi. Model isoterm Freundlich dan Temkin paling sesuai untuk menggambarkan mekanisme adsorbsi ion Fe3+ pada pektin dengan R2 berturut-turut 0,9871 dan 0,9591. Data parameter termodinamika membuktikan bahwa adsorpsi ion Fe3+ bersifat eksotermis dan berlangsung secara tidak spontan pada rentang temperatur 20 hingga 60ᵒC. Penelitian ini menunjukkan bahwa kulit pisang dapat dimanfaatkan sebagai adsorben murah yang menjanjikan untuk menghilangkan ion Fe3+ dalam air.