26 August 2016 in Microsystems & Nanoengineering
While there are innumerable devices that measure temperature, the nonvolatile measurement of thermal history is far more difficult, particularly for sensors embedded in extreme environments such as fires and explosions. In this review, an extensive analysis is given of one such technology: thermoluminescent microparticles. These are transparent dielectrics with a large distribution of trap states that can store charge carriers over very long periods of time. In their simplest form, the population of these traps is dictated by an Arrhenius expression, which is highly dependent on temperature. A particle with filled traps that is exposed to high temperatures over a short period of time will preferentially lose carriers in shallow traps. This depopulation leaves a signature on the particle luminescence, which can be used to determine the temperature and time of the thermal event. Particles are prepared—many months in advance of a test, if desired—by exposure to deep ultraviolet, X-ray, beta, or gamma radiation, which fills the traps with charge carriers. Luminescence can be extracted from one or more particles regardless of whether or not they are embedded in debris or other inert materials. Testing and analysis of the method is demonstrated using laboratory experiments with microheaters and high energy explosives in the field. It is shown that the thermoluminescent materials LiF:Mg,Ti, MgB4O7:Dy,Li, and CaSO4:Ce,Tb, among others, provide accurate measurements of temperature in the 200 to 500 °C range in a variety of high-explosive environments.
1 June 2015 in Applied Optics
This paper describes the physical processes that occur when high-power continuous-wave laser light interacts with absorbing particles on a low-absorption optical surface. When a particulate-contaminated surface is illuminated by high-power continuous-wave laser light, a short burst of light is emitted from the surface, and the particles rapidly heat over a period of milliseconds to thousands of degrees Celsius, migrating over and evaporating from the surface. The surviving particles tend to coalesce into larger ones and leave a relatively flat residue on the surface. The total volume of the material on the surface has decreased dramatically. The optical surface itself heats substantially during illumination, but the surface temperature can decrease as the material is evaporated. Optical surfaces that survive this process without catastrophic damage are found to be more resistant to laser damage than surfaces that have not undergone the process. The surface temperature of the conditioned surfaces under illumination is lower than that of unconditioned surfaces. These conditioning effects on particles occurred within the first 30 s of laser exposure, with subsequent laser shots not affecting particle distributions. High-speed photography showed the actual removal and agglomeration of individual particles to occur within about 0.7 ms. Elemental changes were measured using time-of-flight secondary ion mass spectroscopy, with conditioned residuals being higher in hydrocarbon content than pristine particles. The tests in this study were conducted on high-reflectivity distributed Bragg reflector coated optics with carbon microparticles in the size range of 20–50 μm, gold particles of size 250 nm, and silica 1 μm in size.
24 January 2019 in Scientific Reports
Laser-Induced optical breakdown often occurs unexpectedly at optical intensities far lower than those predicted by ultra-short pulse laser experiments, and is usually attributed to contamination. To determine the physical mechanism, optical coatings were contaminated with carbon and steel microparticles and stressed using a 17 kW continuous-wave laser. Breakdown occurred at intensity levels many orders of magnitude lower than expected in clean, pristine materials. Damage thresholds were found to strongly follow the bandgap energy of the film. A thermal model incorporating the particle absorption, interface heat transfer, and free carrier absorption was developed, and it explains the observed data, indicating that surface contamination heated by the laser thermally generates free carriers in the films. The observed bandgap dependence is in direct contrast to the behavior observed for clean samples under continuous wave and long-pulse illumination, and, unexpectedly, has similarities to ultra-short pulse breakdown for clean samples, albeit with a substantially different physical mechanism.
23 June 2009 in Optics Letters
A mechanical design technique for optical coatings that simultaneously controls thermal deformation and optical reflectivity is reported. The method requires measurement of the refractive index and thermal stress of single films prior to the design. Atomic layer deposition was used for deposition because of the high repeatability of the film constants. An distributed Bragg reflector was deposited with a predicted peak reflectivity of 87.9% at 542.4 nm and predicted edge deformation of −360 nm/K on a 10 cm silicon substrate. The measured peak reflectivity was 85.7% at 541.7 nm with an edge deformation of −346 nm/K.
9 April 2020 in Applied Optics
Germanium is one of the most commonly used materials in the longwave infrared ( ), but ironically, its absorption coefficient is poorly known in this range. An infrared photothermal common-path interferometry system with a tunable quantum cascade pump laser is used to measure the absorption coefficient of pure undoped germanium as a function of wavelengths between 9 and 11 µm, varying between about 0.15 and over this range.
5 March 2018 in Optics Express
A Yb-doped fiber laser is used to accelerate and evaporate absorbing particles in air. Optical intensities of 1MW/cm2 and 2MW/cm2 illuminate stainless steel particles. These particles are accelerated to velocities of tens of meters per second before evaporating within a few tenths of a millisecond. Position measurements are made using direct imaging with a high-speed camera. A fundamental system of coupled differential equations to track particle momentum, velocity, mass, radius, temperature, vapor opacity, and temperature distribution is developed and shown to accurately model the trajectories and lifetimes of laser heated particles. Atoms evaporating from the particle impart momentum to the larger particle, which accelerates until it is slowed by drag forces. Heat transfer within the evaporating particles is dominated by radiation diffusion, a process that usually only dominates in astrophysical objects, for example in the photospheres of stars.