24 August 2018 in IEEE Transactions on Industrial Electronics
Absolute magnetic encoders (AMEs) use two magnets: a ring multi-polar magnet generating highresolution and improving the accuracy for the encoder, and a bipolar magnet in the center calculating the number cycle of multi-polar magnet signals. The phase outputs of these AMEs are tracked from the sinusoidal signals of the multi-polar magnet. However, these sine/cosine signals are disturbed by amplitude differences, offsets, phase-shift, harmonic components, and random noise. In order to solve this problem, we present an adaptive linear neuron based on a third-order phase-locked loop (ALN-PLL) to improve the accuracy of AMEs. The proposed approach consists of two main parts: The first part is an ALN algorithm that uses the phase feedback of the third-order PLL in order to build the mathematical model of input signals, and then reject the disturbances. The second part is a third-order PLL that is designed based on a dominant pole approximation algorithm. The proposed PLL can reduce noise and eliminate DC-error during the phase step, frequency step, and frequency ramp. The simulation and experimental results demonstrate the effectiveness of the proposed approach.
13 September 2018 in IEEE Transactions on Industrial Electronics
This paper proposes a method to improve the accuracy of an absolute magnetic encoder (AME) by using harmonic rejection and a dual phase-locked loop (HRDPLL). The encoder consists of two permanent magnets: an edge-located multipolar magnet (MPM) as well as a center-located bipolar magnet (BPM), in which the signalprocessing accuracy of the MPM is crucial for achieving high accuracy of the entire encoder. However, the MPM signals are disturbed by nonidealities such as dc offsets, amplitude mismatch, low- and high-order harmonics, and random noises. In this paper, the harmonic rejection (HR) approach investigates the characteristics of nonidealities of the phase detector and rejects them by using gradient descent. In addition, the dual phase-locked loop (DPLL) remains robust by maintaining a zero steady-state error during a phase jump, a constant frequency and ramp frequency. The proposed method is simulated with Matlab software and implemented in ARM STM32F407ZG. The obtained results demonstrate efficient performance. This method can be applied to any use of quadrature sinusoidal signals, such as in power grids and in permanent-magnet synchronous motor phase detection.
25 January 2021 in IEEE Access
This paper proposes a linear compensator algorithm to improve the performance of an absolute multipolar magnetic encoder (AMPME). An AMPME is an absolute magnetic rotary encoder that uses a multipolar magnet (MPM) to increase the resolution. The resolution can be dramatically increased in proportion to the number of poles in the MPM. However, various hardware problems that occur during the encoder manufacturing process degrade the AMPME performance. Also, harmonic components occur in the raw data due to various problems, such as the resistance error of the analog circuit, magnetic field overlap between the magnets, position error between the sensor and magnet, and pole-pitch difference. In particular, during the magnetization process of the MPM, the pole-pitch difference becomes a problem when the sizes of each pole are not uniform. This problem causes harmonic components that reduce the absolute position accuracy. To solve these problems, this paper proposes a linear compensation method. The proposed linear compensator consists of two parts. The first part is the enhanced ratiometric linearization for phase calculation and calibration. The second is the phase compensator for removing the phase difference via the pole-pitch difference of the MPM. The linear compensator improves various parameters by precomputing the offset, amplitude, and phase corrections. After compensating for sinusoidal signals, the linear compensator applies appropriate parameters at the appropriate times. This method is faster, easier to set up, and more accurate than the conventional method. Furthermore, this method is experimentally verified against the existing harmonic rejection method. Experimental results are provided to verify the effectiveness of the proposed method.
12 June 2020 in IEEE Transactions on Industrial Electronics
This article proposes a method to improve the accuracy of a vernier absolute magnetic encoder. The encoder consists of a master and a nonius multipolar magnetic track. Sinusoidal signals from the master and nonius tracks are used to infer the absolute information. Unfortunately, these signals are contaminated by nonideal factors such as different amplitudes, dc-offsets, phase shifts, and random noise. Moreover, harmonics existing in the encoder signals distort the vernier principle and significantly affect the accuracy of the encoder. To address these problems, the present article proposes an efficient method with three main parts. The first is an observer phase-locked loop (OPLL), which is used to estimate the phase and eliminate the nonideal factors. The second is nonlinear phase compensation, which is used to correct the vernier principle that deviated due to the existing harmonics. Finally, a pole pitch compensation method is introduced to modulate the master phase angle from the OPLL to eliminate the harmonic distortion. The proposed method can eliminate the nonideal factors, harmonic distortion and improve the accuracy of the encoder. All the proposed methods were implemented on an ARM STM32F407ZG. The experimental results confirm the validity of the proposed method for practical applications.
24 December 2019 in IEEE Transactions on Instrumentation and Measurement
This paper presents a self-referencing lookup-table algorithm to enhance the multi-turn accuracy of a Battery-free multi-turn absolute magnetic encoder. The encoder consists of a single-turn angle for the measurement of the degree of rotation within 2π using a multipolar magnet to achieve high resolution and a multi-turn counter to monitor the total number of revolutions made by the encoder’s shaft through the different angles of the four bipolar magnets (BPM) based on four shaft gears. However, the signals from the BPMs are affected by factors such as amplitude mismatch, dc-offsets, random noises, and harmonic components which are as a result of electrical and mechanical distortions. To solve this problem, this paper suggested a method derived from the single-turn angle and the raw signals from the BPMs to generate the lookup-tables for multi-turn angles. These angles eliminate the effects of the disturbances. Additionally, a multi-turn compensation algorithm is suggested to compensate for the number of revolutions made by the encoder. The proposed methods are simulated in MATLAB software and implemented in ARM STM32F407ZG. The effectiveness of the proposed method is demonstrated by the obtained results.
10 March 2022 in IEEE Access
This study describes a hands-on in-vehicle network (IVN) training course for automotive engineers, particularly for learners with different prior knowledge. We collected essential content to educate those with different backgrounds on IVN-related information, which is essential in practice. The course aims within a short period to effectively educate engineers working in the industry on IVN systems, and explains how to employ embedded systems and graphical user interfaces (GUIs) for this purpose. At the end of the training, the level of knowledge before and after training was compared to evaluate the training results, and engineers’ responses were recorded.