Second-mode instability plays an important role in the transition of a hypersonic boundary layer. The second-mode wave on a flared cone at Mach 6 has been investigated experimentally through the Nanoparticle-tracer based Planar Laser Scattering (NPLS) technique in this paper. Different behaviors of the second-mode wave ranging from linear growth to deformation are visualized under different unit Reynolds numbers. The propagation velocity of the second-mode wave is quantitatively calculated, and the spectral properties of the second-mode wave have been analyzed by the power spectrum density. The characteristic frequency of the second-mode wave calculated from the NPLS images agrees well with the results measured by the transducers. Evolution of the wall-normal distribution of disturbance shows that high frequency harmonics are generated during the growth process of the second-mode wave and its normal distribution range shrinks with the increase in its frequency. The bispectral analysis indicates that the high degree of phase coupling may be the reason for the deformation of the second-mode wave. The nonlinear interaction between the disturbance waves is strong during the deformation stage of the second-mode waves.
1 August 2018 in Journal of Materials Science: Materials in Electronics
Polymer-based dielectric nanocomposites as raw materials of dielectric capacitors used in advanced electronics and electrical systems have a great application prospect but remain a huge challenge to energy storage performance in high electric fields. In this work, MgAl layered double hydroxide (MgAl LDH) nanosheets loaded with Ni nanoparticles were designed and synthesized, and incorporated into polyvinylidene fluoride (PVDF) to fabricate Ni–MgAl LDH/PVDF nanocomposites with high energy density. The effect of Ni–MgAl LDH nanosheet content (0.2 to 0.8 wt%) on the energy storage performance of MgAl LDH/PVDF nanocomposites was studied. As a result, after adding 0.6 wt% Ni–MgAl LDH nanosheets, the nanocomposites obtained the highest energy density 23.87 J cm−3 (at 640 kV mm−1) and the charge–discharge efficiency reached 65%, which was 76% and 18% higher than that of pure PVDF, respectively. This improvement could be attributed to the multiple functions of Ni–MgAl LDH nanosheets under an applied electric field. On the one hand, Ni nanoparticles on the surface of the MgAl LDH nanosheets could enhance the interfacial conductivity, form plenty of parallel micro-capacitors and produce Coulomb blockade effect, which resulted in high dielectric constant and high breakdown strength. On the other hand, two functions contributed by MgAl LDH nanosheets, homogenizing the electric field and inhibiting the growth of the electric tree coming from its medium dielectric constant and sheet structure, were beneficial to increase the breakdown strength. Furthermore, finite element simulations were employed to explain the mechanism of improved dielectric properties of the Ni–MgAl LDH/PVDF nanocomposites.
Curvature plays a crucial role in evolving supersonic cooling film flow-field structures. Flow-field structural images were captured using nanotracer-based planar laser scattering,, and wall pressure values were obtained using experimentally validated numerical simulations. A supersonic cooling film is tangentially injected at the Mach number of Maj = 2.3 into a laminar boundary layer at a mainstream of Ma = 6. The supersonic cooling film inhibits mixing-layer instability on the convex curved wall (CV) and promotes it on the concave curved wall (CC). After increasing the total incoming pressure, the reduction ratio of static pressure (RSP) between the supersonic cooling film and the mainstream flow causes a delay in the position of the mixing-layer instability, smaller-scale vortex structures, and decreased flow velocity of the typical vortex structures on the CC and CV. The wall pressure increases for the CV and decreases for the CC, indicating that the supersonic cooling film suppresses the changes in wall pressure due to curvature. The supersonic cooling film suppresses the decrease in the impulses for bulk dilatation (Ip) due to convex curvature and the increase in Ip due to concave curvature. The growth rate of Ip on the CC increases from −15% to −8% and decreases on the CV from 31% to 12% in the bending impulse (IΦ) range of |IΦ| = 1.337–3.624 for a total inlet pressure of 0.5 MPa. Increasing the RSP could control the Ip values on curved surfaces more effectively. The results of this study can be applied to cooling the infrared optics window on hypersonic vehicles.