In this letter, we proposed a bendable wideband dual-polarization low-profile conformal phased array antenna. The antenna element is an Invert-F fed stacked-patch antenna. It provides an active VSWR < 3 for 10.7 GHz to 12.75 GHz in the principal planes. The proposed phased array antenna employs a row modular architecture, which enables it to bend to a cylindrical geometry. Both the antenna aperture and the active components of the conformal phased array antenna are considered for bending in the letter. A prototype conformal phased array antenna with 8 rows of 4 dual-polarization antenna element was fabricated, assembled and measured. Wide-angle beam scanning is achieved by electronically scanning along the curved axis of the cylindrical conformal phased array antenna. Moreover, there is no grating lobe when scanning down to 60°.
29 March 2019 in IEEE Transactions on Antennas and Propagation
A deployable log periodic dipole antenna (DLPDA) is proposed. The antenna consists of pairs of collapsible steel tape springs (as the dipoles), a novel stretchable zigzag double-sided parallel stripline (ZDPS) (as the boom), and a coplanar waveguide on one side of the parallel striplines to guide the electromagnetic wave from the backend to the frontend. As a result, the proposed antenna becomes foldable and can be stored in a small volume prior to deployment. A design guideline for the DLPDA is given based on the simplified circuit model. Furthermore, the ZDPS which is found as a slow-wave structure, has been studied. The empirical equations are derived to obtain its characteristic impedance and propagation constant, which are the key parameters for the design guideline. One prototype of the DLPDA has been fabricated and tested. The deployment mechanism of the prototype has been successfully demonstrated using compressed air in a lab. The prototype has a stowed volume of <2000 cm3, which is only 2% of the volume in fully deployed state.
18 December 2020 in IEEE Transactions on Antennas and Propagation
In this paper, a compact 3-D printed orthogonal mode transducer (OMT) is proposed. Unlike conventional OMT that uses long extended transition for port matching, the proposed design uses embedded fences and novel short tapered triangular prism to replace such long transition. In this way, the size of the OMT can be reduced. The tapered triangular prism effectively improves the matching of the perpendicularly-transverse port without affecting the performance of the port aligned with the common port. The fence acts as a polarizer grid to further reduce the reflection of incident waves back into the input port. The return loss and isolation of the very compact OMT are better than 16 dB and 40 dB, respectively, from 2.65 GHz to 3.2 GHz. Considering the complicated geometry of the proposed OMT, 3-D metal printing technology is adopted as the fabrication method. The measurement results agree well with the simulation results.
23 January 2023 in IEEE Open Journal of Antennas and Propagation
In this paper, a deployable wideband differential-fed dual-polarized high-isolation patch antenna array is proposed. To achieve dual polarization, every element has two pairs of differential ports. Because of the differential design, the couplings from the adjacent ports (the other pair of ports) are canceled and high isolation between the two polarization is achieved. In addition, capacitive feeds are applied to enhance the bandwidth. By integrating with two planar Marchand baluns, the two pairs of the differential ports are excited for dual polarization. Then, the wideband dual-polarization patch antenna element is expanded to a 4×4 antenna array for better gain. In order to achieve deployment, we present a novel foldable mechanism suitable for low-frequency patch antenna array, which is different from the conventional design on the flexible printed board. The deployment concept is presented. One prototype is fabricated and measured. Its operating band is from 1.15 GHz to 1.35 GHz. The peak gains of the two polarizations are 14.4 dBi and 14.1 dBi respectively.
A novel low profile wideband monocone antenna with low cost printed circuit board (PCB) fabrication technology is proposed. Step structures are proposed to simulate the cone structure of traditional monocone antennas, based on three stacked layers of PCB with equal height. The monopole-like radiation patterns and the input reflection coefficients below -10dB are achieved from 2.06GHz to 7.36GHz. Techniques like applying the shorting pins and the annular ring are used to decrease the lowest working frequency. The thickness of the proposed antenna is reduced to only about 0.06λ 0 at the lowest frequency. The ripples in the H-plane pattern is always below 0.5dB.