7 October 2014 in Materials and Manufacturing Processes
1 November 2006 in IECON 2006 - 32nd Annual Conference on IEEE Industrial Electronics
In this study, a new control algorithm for three-phase shunt active power filter (APF) is proposed without load and filter current measurement. The proposed control method, based on instantaneous reactive power (IRP) theory, requires only measuring the source currents in order to reduce the number of current sensors (CSs) required in the conventional control approach. The source currents are exactly in phase with the line voltages and approximately sinusoidal waveform after compensation. The proposed control technique has been simulated Matlab/Simulink and tested under thyristor bridge rectifier load condition, and validated with a 10 kVA/380 V experimental prototype based on digital signal processor (DSP) TMS320F2812. Both simulation and experimental test results demonstrate viability of the proposed method, successful in meeting the IEEE 519-1992 recommended harmonic standard limits
18 September 2013 in High Temperature Materials and Processes
In this study, the effects of thixoforming, both equal channel angular pressing (ECAP) and thixoforming on high cycle fatigue and fatigue surface morphology of AA7075 have been examined. Experiments are carried out with the same sample materials (AA7075) at a constant temperature (483 K) and the ``C'' route for 4 passes at ECAP process. In the process of thixoforming is 20 min at 888 K for waiting and 1 min at 673 K for pressing implemented. 140 MPa, 120 MPa and 100 MPa strength values were used at fatigue tests. The microstructural characterizations of the samples were carried out by using optical microscope (OM), scanning electron microscope (SEM) and transmission electron microscope (TEM). This study is an attempt in detail to transformation fine and spherical grain structure with thixoforming process of minimized grain structure by ECAP. As a result of this study, it was seen that ECAP (1 pass) + semi-solid processing (SSP) applied samples have the highest hardness value (171 HV). When the values that are obtained after fatigue strength analyzed, SSP applied materials' property gave the best results and ECAP (1 pass) + SSP applied samples' results were second. When the both process applied materials' optimum values are investigated, it was observed that ECAP 1 pass + SSP applied material is more appropriate in terms of high hardness and fatigue life.
27 September 2024 in Dokuz Eylül Üniversitesi Mühendislik Fakültesi Fen ve Mühendislik Dergisi
Kapalı veya açık ortamlarda artış gösteren hava kirliliği insan vücudu üzerinde çeşitli hastalıklara yol açabilmekte ve zaman içerisinde Covid19 gibi yeni bir pandemik reaksiyona sebebiyet verebilmektedir. Kapalı ortamlardaki hava kirlilik oranı, açık ortamlara göre daha fazladır ve günlük hayatımızın büyük bir bölümü kapalı ortamlarda geçtiği için bu ortamların temizlenmesi gerekmektedir. İnsan yaşamının temiz hava ihtiyacını gidermek ve ortamların kirlilik oranını azaltmak için hava temizleme cihazları giderek artan bir ilgi görmeye başlamıştır. Çalışma kapsamında 200 m^3/h hacimsel debi kapasitesi olan bir hava temizleme cihazı incelenmiştir. Ortam şartları, filtre basınç-debi grafikleri ve motor dönüş hızı Hesaplamalı Akışkanlar Dinamiği (HAD) sayısal çalışmasına sınır şartı tanımlanarak Deney-HAD karşılaştırması yapılmıştır. Deneysel olarak ayrıca Ses Basınç Seviyesi (SPL) ölçümlenmiştir. HAD sayısal çalışmaları SolidWorks Flow Simulation (SWFS) ticari yazılımı kullanılarak gerçekleştirilmiştir. Hava giriş-çıkış bölgesine ortam basınç değeri (P_s=101235 Pa), sıcaklığı (T_o=20°C) ve motor dönüş hızı (2000 RPM) tanımlanırken havalandırma cihazının çıkışındaki hacimsel debisi deney doğrulama parametresi olarak kullanılmıştır. SWFS yazılımında bulunan k-ℇ Reynolds Averaged Navier-Stokes (RANS) türbülans modeli seçilmiş ve doğrulanan ağ yapısında cihaz içerisinde oluşan türbülanslı bölgeler, tersinir akışlar ve sadece akışkana bağlı akustik ses gücü şiddeti iyileştirilerek ortaya yeni bir model konmuştur. İyileştirilmiş model ile mevcut model arasında ses basınç seviyesinde 2,7 dB(A) ve harcanan güçte %10,52 oranında azalma tespit edilmiştir. Çalışma kapsamında mevcut ses yalıtım malzemesine ek olarak 2 farklı ses yalıtım malzemesi daha deneysel olarak incelenmiş toplamda 3 farklı ses yalıtım malzemesi ses basınç seviyesi arasında 6,4 dB(A) fark olduğu tespit edilmiştir.