Min-Woo Kim

Min-Woo Kim

Auto-generated profile, based on publicly available information

Min-Woo Kim

Display Electronics Development Team,Samsung Display Ltd.,Yongin-si,Republic of Korea

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 September 2017 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
HGHui-Dong Gwon
Hui-Dong Gwon
JBJun-Suk Bang
Jun-Suk Bang
KYKye-Seok Yoon
Kye-Seok Yoon
SPSe-Hong Park
Se-Hong Park
SPSang-Hui Park
Sang-Hui Park
GCGyu-Hyeong Cho
Gyu-Hyeong Cho
This paper presents a 2-phase 3-level (2P3L) envelope tracking supply modulator (ETSM) for a 20 MHz LTE RF power amplifier (PA) as a solution for the envelope tracking (ET) system. This 2P3L ETSM that is composed of only switching converters achieves high efficiency, fast transient response, and a small output current ripple. To properly operate the proposed 2P3L ETSM, 4 PWM signals with a 90° phase shift from each PWM signal are required without any mismatch between duty cycles. To remove the mismatch, a time-division multiplexing comparator (TDMC) and a duty-cycle calibrator (DCC) are proposed. Thanks to the proposed techniques, the proposed ETSM fabricated in 0.18 μm CMOS achieved the highest peak dynamic efficiency of 88.6% with a LTE20 signal, which is superior to the state-of-the-art systems.

9 June 2017 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
MKMin-Woo Kim
Min-Woo Kim
JKJi H. Kim
Ji H. Kim
YCYeonje Cho
Yeonje Cho
MKMinsik Kim
Minsik Kim
BCBo H. Choi
Bo H. Choi
CRChun T. Rim
Chun T. Rim
A prototype of a high-resolution synthesized magnetic field focusing (SMF) system for a possible application to radio frequency (RF) barcodes is proposed in this paper. It was recently found that coordinated control of array coil currents makes it possible to focus magnetic field, which is requisite for medical imaging, wireless power, and RF identification. Different from conventional phased array RF antennas, SMF is independent of frequency, which is quite promising for various applications. In this paper, an array of rectangular air coils is proposed, and various implementation issues, such as accurate control of coil currents and compact RF barcode design, are newly suggested. A prototype of an SMF system composed of a transmitter (Tx), an RF barcode, and a receiver (Rx) was implemented at below 1 MHz operating frequency. The Tx includes modularized control drivers, full-bridge switching converters, and 16 arrayed air coils, where the RF barcodes proposed in this paper include a self-resonating circuit at 20 mm × 20 mm and a tunable resonating circuit at 15 mm × 15 mm. In this way, a 5 mm resolution at a distance of 20 mm was achieved for the Tx arrayed air coils with spacing of 5 mm, which is about four times sharper magnetic field focusing compared to a nonfocusing conventional coil. Furthermore, the proposed SMF system allows the designed 5-bit RF barcode array to be fully distinguishable at a 15 mm distance.

21 May 2018 in IEEE Sensors Journal
Verified
Journal Article
Closed access
MKMin-Woo Kim
Min-Woo Kim
DKDong-Kyu Kim
Dong-Kyu Kim
TKTetsuhiro Kodani
Tetsuhiro Kodani
TKTakashi Kanemura
Takashi Kanemura
HGHui-Dong Gwon
Hui-Dong Gwon
HKHyun-Sik Kim
Hyun-Sik Kim
A force-touch (z-axis) sensor for display applications has attracted considerable attention. The z-axis sensing layer can be realized by a transparent piezoelectric thin-film due to its superior characteristics, such as thinness, flexibility, and an optical transparency. However, this film responds not only to pressure but also to thermal changes (pyroelectric characteristic), which is a major obstacle to commercialization. This paper presents a thermal-variation insensitive, force-touch sensing system using a transparent piezoelectric thin-film. In conjunction with optimizations in analog front-end design for high gain and high speed, the threshold-based digital processing scheme, which effectively rejects pyroelectric signals and noises, is proposed. To validate the proposed design and method, the electronic readout system board composed of analog circuits and an 8-bit microcontroller unit was implemented, and it read out the force-touch signal with a 10-bit resolution in power consumption of 6.5 mW. The implemented readout system was experimentally verified with a 3.9-inch PVDF-copolymer piezoelectric thin-film sensor, with a thickness of 20 μm. The system achieves a force -to-signal gain of 0.6 V/N in a range of 0.3 to 2.5 N with high linearity. The capability to reject a pyroelectric signal up to ±Δ10°C/s was also proved through a thermal-shock experiment.


4 September 2023
Verified
Conference Paper
Closed access
MKMin-Woo Kim
Min-Woo Kim
JKJi-Won Kim
Ji-Won Kim
KMKyung-Hwan Moon
Kyung-Hwan Moon
JLJung-Bong Lee
Jung-Bong Lee
WSWon-Ju Shin
Won-Ju Shin
In this paper, a new definition of the EMI reduction mechanism is presented, and it is expected to improve the data reception sensitivity of mobile devices through EMI reduction. The main contents are to introduce a method to reduce EMI more than 90% and to identify jitter level is the same as SSCG OFF at the same time by adding average-time concept. Data reception sensitivity in wireless communication is characterized by reviewing the average data reception error rate for a specific period of time. The average-time concept, which is the key to reduce the EMI. SSCG+ is a method in which the display clock harmonics reduces the time probability in the wireless communication band. It is changing the datarate from several Mbps for each section in OLED display. Even if the fundamental clock frequency is changed by only a few kHz, the clock harmonic frequency between the changes is shifted by several MHz in the wireless band. In other words, the advantage is to reduce the probability that the clock harmonics exist in the wireless band because the clock frequency is continuously changed based on the discrete frequencies. In addition, the signal integrity of SSCG+ shows that the jitter characteristics are the same as that of SSCG off, because SSCG+ has a constant transmission speed in the active data sections in display. This paper proposes a method for improving the jitter and EMI levels at the same time.