28 December 2020 in IEEE Access
Architecture modeling, simulation, and test verification are performed to meet the requirements of multi-domain modeling and simulation of tractor power shift transmission (PST). The principles of architecture modeling and high level architecture (HLA) are analyzed, and the PST architecture modeling connotation and simulation system structure are studied. Then the dynamic principles of PST mechanical, hydraulic and control subsystems are analyzed in the preparation phase, sliding friction phase and holding phase of clutch engagement. To build the PST system simulation model, the simulation models and components of the three subsystems are established, and the object and interaction classes of the simulation object model (SOM) for each component are defined. After that, the parameter mapping relationship between the components is analyzed, the interfaces between the simulation components and HLA are encapsulated, and the simulation component running sequence is analyzed. Finally, the PST clutch engagement law under tractor shift conditions is simulated and tested. The relative error and correlation coefficient between the simulated and test data of shift solenoid valve drive current are used as indexes to evaluate the PST system simulation model. The results show that the simulated drive current curves are consistent with the test ones. The maximum error between the simulated and test shift time appears at the third gear downshift point, with a value of 7.89%, and the minimum correlation coefficient value between the simulated and the test drive current at all shift points is 0.92, which indicate that the PST system simulation model is effective and accurate.
13 February 2025 in PLOS ONE
In the research on energy optimization control for parallel hybrid tractors, torque has been identified as a crucial factor influencing the tractor’s fuel economy, operational efficiency, and agricultural development. This study focuses on the tractor’s overall demand torque as the primary research parameter and designs a comprehensive scheme for the parallel hybrid tractor. The study includes the design of power system parameters and the construction of a dynamic model for the entire machine. Based on this, an energy optimization control strategy, termed adaptive immune particle swarm optimization fuzzy control strategy (AIPSOFCS), is proposed. Simulation analysis is performed using representative plowing conditions, and AIPSOFCS is compared with the power follow control strategy (PFCS) and fuzzy control strategy (FCS). The results indicate that AIPSOFCS demonstrates higher fuel economy and operational efficiency compared to PFCS and FCS. In the plowing conditions, the fuel economy of AIPSOFCS is reduced by 8.45% and 2.93% compared to PFCS and FCS, respectively. In the rotary tillage conditions, the fuel economy of AIPSOFCS is reduced by 2.40% and 4.07% compared to PFCS and FCS, respectively. Finally, hardware-in-the-loop (HIL) testing of the controller confirms the effectiveness of AIPSOFCS. This research is of significant importance for enhancing the fuel economy and operational efficiency of parallel hybrid tractors and provides theoretical support and reference for the future.
3 December 2024 in Engineering Fracture Mechanics
27 October 2020 in IEEE Access
A dynamic loading system of a power wagon is studied to solve the problems of low loading precision, slow response speed, and poor adaptive capability of a power wagon in an agricultural vehicle traction test. The load feature of an engine is analyzed under different gear locations, governor handle positions, and vehicle speeds. Meanwhile, the load feature of an eddy current retarder is examined based on a backpropagation (BP) neural network proportional–integral–derivative (PID) control algorithm. The mathematical model for the loading system is established. The time domain model for traction is refactored by a white noise filter according to the power spectral density function. To improve the dynamic loading performance of the eddy current retarder, the BP neural network PID control algorithm is used to change its exciting voltage to achieve an accurate simulation of the actual working load. The effectiveness and practicability of this control algorithm are validated by comparing its system output response dynamic characteristics with those of the traditional PID control algorithm. Simulation results show that the output error is less than 2.8% and the maximum delay is 56.5 ms when the BP neural network PID control is used. On the basis of this result, the traction property of a tractor with several wheels is tested on the road. The test and analysis results indicate that the output loads of the loading system accurately simulate the field actual load of the tractor. The maximum output load value of the system is 42–48 kN and the applicable speed range is 0–25 km/h. The output error is less than 3.5% and the maximum delay is 85.6 ms.