1 August 2023 in Physics of Fluids
The influence of the moving endwall on the behavior of the tip leakage flow in compressors holds substantial significance. This work investigates the unsteadiness of the compressor's tip leakage flow under the impact of the moving endwall, employing both experimental methods and unsteady Reynolds-averaged Navier–Stokes (URANS) simulations. First, a numerical decomposition technique is proposed to isolate the tip leakage flow within a controlled diffusion airfoil (CDA) cascade. Subsequently, URANS simulations based on the CDA cascade are conducted at various incidence angles (−6° to +7°), tip clearances (clearance to chord: 0.83% to 3.33%), and flow coefficients (0.4 to 0.6), and additional URANS simulations based on the Virginia Tech cascade are also performed. The results indicate that the moving endwall induces a greater inclination of the tip leakage flow in the pitchwise direction, allowing it to impinge upon the pressure side of the adjacent blade. The impingement, if sufficiently intense, leads to the periodic generation of unsteady tip leakage flow by altering the blade loading. Moreover, the degree of unsteadiness diminishes significantly as the endwall speed and clearance height decrease. Additionally, it is observed that the breakdown of the tip leakage vortex does not serve as the root cause of the periodic unsteadiness. These findings underscore the critical role played by the moving endwall in the unsteadiness of the compressor's tip leakage flow.
19 September 2022 in Journal of Turbomachinery
11 December 2019 in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
The paper presents an advanced parametric method of blade stacking lines in terms of sweep and lean based on controlled curvature. To the knowledge of the authors, there is no related approach reported in open literature that uses Bezier spline as the radial curvature distribution to improve the smoothness of the blade surface; most previous studies ignored the discontinuous slopes of curvature of the parametric curves. The parametric method called curvature-controlled stacking-line method (CCSLM) is performed by changing the magnitude of the sweep or lean. A fourth Bezier spline is adopted to define the curvature of spanwise stacking line directly ensuring surface smoothness. Then, the redesign cascades are created by sectional profiles stacked along the radial stacking lines which are obtained by twice integrating the Bezier spline. Then, the advanced method is conducted to optimize a high-subsonic controlled diffusion airfoil at design point, where the blade shape is generated in terms of lean. A single-objective optimization is performed using Kriging model and genetic algorithm to optimize total pressure loss, and the optimized geometry is obtained. The optimization results show that the blade design CCSLM has significant effects on the endwall flow vortex as well as radial loading distribution. The reduction of total pressure loss and secondary flow is also observed, and the aerodynamic performance is well improved compared with the original cascade.
20 February 2020 in Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy
Humpback whale’s flipper with leading-edge tubercles has been attracting aerodynamic and hydrodynamic researchers’ attentions by its stall-delayed characteristics. Inspired by this, the undulating configuration is used in a highly loaded compressor cascade as a new type of passive flow control technique. A new model of undulating compressor blade is studied in this paper. To investigate the effect of the undulating configuration on cascade performance without the impact of endwall, steady Reynolds-averaged Navier–Stokes simulations of infinite-span cascades are carried out with and without undulations at an inlet Mach number of 0.5. A parametric study is performed to conclude that, with a suitable wavelength, the undulating blade could achieve a rise in diffusion capacity, accompanied by 12.9% reduction in total pressure loss coefficient at a post-stall incidence angle of 8°, whereas it produces negligible impact in cascade performance at 0° incidence angle. Flow visualization further reveals that wavelength is a crucial parameter, determining the spanwise space for the formation of streamwise vortices. Undulating blades could produce positive effects with maximum magnitude when the counter-rotating streamwise vortices take dominant position along span with an appropriate size.
1 September 2024 in Physics of Fluids
Deep transfer learning is frequently employed to address the challenges arising from limited or hard-to-obtain training data in the target domain, but its application in axial compressors has been scarcely explored thus far. In this paper, a multi-objective optimization framework of a transonic rotor is established using deep transfer learning. This framework first pre-trains deep neural networks based on the peak efficiency condition of 100% design speed and then fine-tunes the networks to predict the performance of off-design conditions based on the small training dataset. Finally, the design optimization of the transonic rotor is carried out through non-dominated sorting genetic algorithm II. Compared to neural networks that are trained directly, transfer learning models can achieve higher prediction accuracy, particularly in scenarios with small training datasets. This is because the pre-trained weights can offer a better initial state for transfer learning models. Moreover, transfer learning models can use fewer samples to obtain an approximate Pareto front, making the optimized rotor increase the isentropic efficiency at both peak efficiency and high loading conditions. The efficiency improvement of the optimized rotor is attributed to the reduction of the loss associated with the tip leakage flow by adjusting the tip loading distribution. Overall, this study fully demonstrates the effectiveness of transfer learning in predicting compressor performance, which provides a promising approach to solving high-cost compressor design problems.