1 August 2006 in Geophysical Journal International
Summary. We present a novel technique for the determination of resistivity structures associated with arbitrary surface topography. The approach represents a t
1 December 2017 in Computers & Geosciences
1 August 2006 in Geophysical Journal International
Summary. We present techniques for the efficient numerical computation of the electrical potential with finite element methods in 3-D and arbitrary topography.
1 July 2011 in Geophysics
Direct-current resistivity surveys usually are performed using steel rods of finite extent and grounding resistance. However, in modeling, electrodes are commonly treated as ideal point sources. We present an approach for numerical computation applying the complete electrode model (CEM), which is known from medical imaging. The electrode surface was discretized, and the partial-differential equations were extended by additional relations incorporating a contact impedance and a condition for the current flow through the electrode surface. We verified the modeling of the electrical potential using an analytical solution for a perfectly coupled half-ellipsoid current source. To quantify the influence of a finite electrode, we computed the electrode effect as the ratio between CEM and point-source solution and investigated its dependence on geometry and contact impedance. Surface measurements using rods of typical spatial extent showed electrode effects on the order of the measuring accuracy for an electrode length/spacing ratio lower than 0.2. However, the effects are more significant for closed geometries such as experimental tanks. A comparison with a point approximation for finite electrodes using point-source locations along the electrode axis showed the best agreement, with points at about 60% of the electrode extension. The contact impedance played a minor role for four-point measurements, contributing only a few percent to the electrode effect. In addition to penetrating electrodes, we investigated surface electrodes with galvanic or capacitive coupling, showing electrode effects on the same order as for penetrating electrodes. An inhomogeneous resistivity distribution clearly increased the size of the effects. We also investigate the use of CEM to simulate current injected through steel-cased boreholes. Finally, we applied the approach with buried ring electrodes to calculate effects caused mainly by geometric disturbances from the borehole.
18 September 2012 in Geophysics
CSCornelia Schmidt-Hattenberger
Cornelia Schmidt-Hattenberger
+2
Surface-downhole electrical resistivity tomography (SD-ERT) surveys were repeatedly carried out to image CO2 injected at the pilot storage Ketzin, Germany. The experimental setup combines surface with downhole measurements by using a permanent electrode array that has been deployed in three wells. Two baseline experiments were performed during the site startup and three repeat experiments were performed during the first year of CO2 injection. By the time of the third repeat, approximately 13,500 tons of CO2 had been injected into the reservoir sandstones at about 650 m depth. Field data and inverted resistivity models showed a resistivity increase over time at the CO2 injector. The lateral extent of the related resistivity signature indicated a preferential CO2 migration toward the northwest. Using an experimental resistivity-saturation relationship, we mapped CO2 saturations by means of the resistivity index method. For the latest repeat, CO2 saturations show values of up to 70% near the injection well, which matches well with CO2 saturations determined from pulsed neutron-gamma logging. The presence of environmental noise, reservoir heterogeneities, and irregularities in the well completions are the main sources of uncertainty for the interpretations. The degradation of the permanently installed downhole components is monitored by means of frequently performed resistance checks. In consistency with the SD-ERT data, these resistance checks indicate a long-term resistivity increase near the CO2 injector. In conclusion, the investigations demonstrate the capability of surface-downhole electrical resistivity tomography to image geologically stored CO2 at the Ketzin site.
1 October 2013 in Review of Scientific Instruments
The LArge Reservoir Simulator (LARS) was developed to investigate various processes during gas hydrate formation and dissociation under simulated in situ conditions of relatively high pressure and low temperature (close to natural conditions). To monitor the spatial hydrate distribution during hydrate formation and the mobility of the free gas phase generated during hydrate dissociation, a cylindrical Electrical Resistivity Tomography (ERT) array was implemented into LARS. The ERT contains 375 electrodes, arranged in 25 circular rings featuring 15 electrodes each. The electrodes were attached to a neoprene jacket surrounding the sediment sample. Circular (2D) dipole-dipole measurements are performed which can be extended with additional 3D cross measurements to provide supplemental data. The data quality is satisfactory, with the mean standard deviation due to permanent background noise and data scattering found to be in the order of 2.12%. The measured data are processed using the inversion software tool Boundless Electrical Resistivity Tomography to solve the inverse problem. Here, we use data recorded in LARS to demonstrate the data quality, sensitivity, and spatial resolution that can be obtained with this ERT array.