“Nanomedicine” is the application of purposely designed nano-scale materials for improved therapeutic and diagnostic outcomes, which cannot be otherwise achieved using conventional delivery approaches. While “translation” in drug development commonly encompasses the steps from discovery to human clinical trials, a different set of translational steps is required in nanomedicine. Although significant development effort has been focused on nanomedicine, the translation from laboratory formulations up to large scale production has been one of the major challenges to the success of such nano-therapeutics. In particular, scale-up significantly alters momentum and mass transfer rates, which leads to different regimes for the formation of nanomedicines. Therefore, unlike the conventional definition of translational medicine, a key component of “bench-to-bedside” translational research in nanomedicine is the scale-up of the synthesis and processing of the nano-formulation to achieve precise control of the nanoscale properties. This consistency requires reproducibility of size, polydispersity and drug efficacy. Here we demonstrate that Flash NanoPrecipitation (FNP) offers a scalable and continuous technique to scale up the production rate of nanoparticles from a laboratory scale to a pilot scale. FNP is a continuous, stabilizer-directed rapid precipitation process. Lumefantrine, an anti-malaria drug, was chosen as a representative drug that was processed into 200 nm nanoparticles with enhanced bioavailability and dissolution kinetics. Three scales of mixers, including a small-scale confined impinging jet mixer, a mid-scale multi-inlet vortex mixer (MIVM) and a large-scale multi-inlet vortex mixer, were utilized in the formulation. The production rate of nanoparticles was varied from a few milligrams in a laboratory batch mode to around 1 kg/day in a continuous large-scale mode, with the size and polydispersity similar at all scales. Nanoparticles of 200 nm were made at all three scales of mixers by operating at equivalent Reynolds numbers (dynamic similarity) in each mixer. Powder X-ray diffraction and differential scanning calorimetry demonstrated that the drugs were encapsulated in an amorphous form across all production rates. Next, scalable and continuous spray drying was applied to obtain dried powders for long-term storage stability. For dissolution kinetics, spray dried samples produced by the large-scale MIVM showed 100% release in less than 2 h in both fasted and fed state intestinal fluids, similar to small-batch low-temperature lyophilization. These results validate the successful translation of a nanoparticle formulation from the discovery scale to the clinical scale. Coupling nanoparticle production using FNP processing with spray drying offers a continuous nanofabrication platform to scale up nanoparticle synthesis and processing into solid dosage forms.
1 September 2018 in Journal of Pharmaceutical Sciences
Flash NanoPrecipitation is a scalable approach to generate polymeric nanoparticles using rapid micromixing in specially designed geometries such as a confined impinging jets mixer or a Multi-Inlet Vortex Mixer (MIVM). A major limitation of formulation screening using the MIVM is that a single run requires tens of milligrams of the therapeutic. To overcome this, we have developed a scaled-down version of the MIVM, requiring as little as 0.2 mg of therapeutic, for formulation screening. The redesigned mixer can then be attached to pumps for scale-up of the identified formulation. It was shown that Reynolds number allowed accurate scaling between the 2 MIVM designs. The utility of the small-scale MIVM for formulation development was demonstrated through the encapsulation of a number of hydrophilic macromolecules using inverse Flash NanoPrecipitation with target loadings as high as 50% by mass.
7 January 2019 in Journal of Visualized Experiments
The formulation of a therapeutic compound into nanoparticles (NPs) can impart unique properties. For poorly water-soluble drugs, NP formulations can improve bioavailability and modify drug distribution within the body. For hydrophilic drugs like peptides or proteins, encapsulation within NPs can also provide protection from natural clearance mechanisms. There are few techniques for the production of polymeric NPs that are scalable. Flash NanoPrecipitation (FNP) is a process that uses engineered mixing geometries to produce NPs with narrow size distributions and tunable sizes between 30 and 400 nm. This protocol provides instructions on the laboratory-scale production of core-shell polymeric nanoparticles of a target size using FNP. The protocol can be implemented to encapsulate either hydrophilic or hydrophobic compounds with only minor modifications. The technique can be readily employed in the laboratory at milligram scale to screen formulations. Lead hits can directly be scaled up to gram- and kilogram-scale. As a continuous process, scale-up involves longer mixing process run time rather than translation to new process vessels. NPs produced by FNP are highly loaded with therapeutic, feature a dense stabilizing polymer brush, and have a size reproducibility of ± 6%.