Arun Kumar Murali

Arun Kumar Murali

Auto-generated profile, based on publicly available information

Arun Kumar Murali

Department of Civil Engineering, Monash University, Melbourne, Australia

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 June 2022 in Rock Mechanics and Rock Engineering
Verified
Journal Article
Open access
PDF file
AMArun Kumar Murali
Arun Kumar Murali
KTKhoa M. Tran
Khoa M. Tran
AHAsadul Haque
Asadul Haque
HBHa H. Bui
Ha H. Bui
Rock-socket pile design predominantly depends on the shaft resistance to support the load at the serviceability state. However, due to limited understanding of the pile–rock interactions, the pile capacity is normally calculated using empirical correlations. In this study, the load-bearing mechanisms of rock-socketed piles were investigated through a miniaturised pile–load test setup in a soft synthetic rock. X-ray CT imaging and numerical discrete element modelling were used to investigate the micro-mechanics influencing the load-bearing mechanisms at the pile–rock interface. The numerical pile model was established based on suitable constitutive models capable of simulating the soft rock behaviour. The analysis of X-ray CT images at various displacements revealed three different interface mechanisms, namely sliding, local shearing and progressive shearing. The numerical model validated this observed micro-mechanics in the rock asperities through the evolution of damage and micro-cracks. Insights from the experimental and numerical results indicated that the height of the rock asperities significantly dictates the failure mode. Results also illustrated that the shaft load–displacement response primarily depends on the forces acting on the leading edges of the pile asperity. In particular, it was observed that the bottom leading edge carried a predominant portion of the shaft loads due to its connectivity with the rock at the base of the pile. Though negligible, the forces on the trailing edges provided valuable information on the contribution of residual shaft resistance by the debris at the interface. Moreover, the numerical studies revealed the different failure modes at the pile–rock interface. The discussions presented in this study provide novel insights into the load-bearing mechanisms of piles socketed in soft rocks, which will help to improve design guidelines in the future.

4 May 2024 in Rock Mechanics and Rock Engineering
Verified
Journal Article
Open access
PDF file
AMArun Kumar Murali
Arun Kumar Murali
AHAsadul Haque
Asadul Haque
HBHa H. Bui
Ha H. Bui
The shaft resistance of rock-socketed piles (RSPs) is primarily influenced by the interactions between the pile, rock and any soft interface materials. This study presents a fundamental experimental and numerical investigation to predict the shaft resistance of model RSPs in soft rocks through a comprehensive shear strength framework incorporating the major variables such as roughness and smear fabric. By calibrating the Discrete Element Method (DEM) results with the experimental outcomes, this study evaluates the load-resistance attributes of RSPs in three different soft rocks for a wide range of roughness and smear configurations. The interface roughness effect of the RSPs in terms of the friction coefficient was correlated with the ultimate shaft resistances, uniaxial compressive strength and Young’s modulus of the rock. The study then incorporated the effect of smear fabric (placement, thickness and area proportion) in the shear strength framework of clean shafts. Comprehensive review of the DEM results revealed that the socket roughness effect diminishes at a critical roughness factor $$({\text{RF}})$$ ( RF ) of 0.4, beyond which the smear predominantly influences the shaft capacity. Following this, the effects of roughness and smear fabric were incorporated into a single equation representing the interface shear strength of RSPs, where the existence of smear results in a maximum reduction of up to 75% of the ultimate shaft resistance. The distinctive feature of this unified interface shear strength framework lies in its integration of the new smear fabric parameter and the linkage to the mechanical properties of soft rocks, which is the limitation of the earlier studies. It thereby sets a strong base for future studies aimed at advancing the pile-rock interface models.

1 January 2021 in Journal of Hazardous, Toxic, and Radioactive Waste
Verified
Journal Article
Closed access
PDF file
SPSughosh Pundarika
Sughosh Pundarika
BPB. Prathima
B. Prathima
MAMurali Arunkumar
Murali Arunkumar
NAN. Anusree
N. Anusree
GBG. L. Sivakumar Babu
G. L. Sivakumar Babu
This paper presents an approach to retrofit an existing municipal solid waste (MSW) dumpsite by enhancing the bioremediation process. The current practice of containing the waste in dumpsites/landfills is considered unsustainable due to their negative impact on the environment, society, and economy. Remediation of the existing open dumpsite helps in recovering the valuable land area at a faster rate due to the reduction in the time required for the waste stabilization process. The problem of leachate treatment can also be addressed adequately during the remediation process. Therefore, remediating an existing dumpsite can be classified as a step toward achieving sustainability in landfilling practice. In this study, an approach for remediating an existing municipal solid waste (MSW) dumpsite in Bangalore city is presented by addressing the three major aspects, viz., landfill gas (LFG), leachate, and the recovery of air space. In order to accelerate the biodegradation of MSW and avoid the possible groundwater contamination, a leachate recirculation system is designed. Modeling tools are used to estimate the LFG emission and to design the leachate collection and recirculation system. The methane oxidation potential of the digested mechanically and biologically treated (MBT) waste as a biotic system media is evaluated using column experiments. Biowindrows are then designed to mitigate the LFG emissions from the dumpsite.

1 July 2024 in Journal of Geotechnical and Geoenvironmental Engineering
Verified
Journal Article
Closed access
AMArun Kumar Murali
Arun Kumar Murali
AHAsadul Haque
Asadul Haque
HBHa H. Bui
Ha H. Bui
KTKhoa M. Tran
Khoa M. Tran

1 January 2024 in Journal of Geotechnical and Geoenvironmental Engineering
Verified
Journal Article
Closed access
AMArun Kumar Murali
Arun Kumar Murali
AHAsadul Haque
Asadul Haque
HBHa H. Bui
Ha H. Bui

16 August 2023 in Geotechnical Testing Journal
Verified
Journal Article
Closed access
PDF file
AMArun Kumar Murali
Arun Kumar Murali
AHAsadul Haque
Asadul Haque
HBHa Hong Bui
Ha Hong Bui
The design of rock-socketed piles at the serviceability state primarily depends on the shaft resistance (skin friction) at the interface, which may be influenced by the presence of weak smear (e.g., bentonite filter cake, soil, and remolded weak rock). To date, two-dimensional direct shear interface testing has been utilized to interpret the effect of smear on the shaft response of bored piles. However, without the nondestructive testing and three-dimensional (3D) visualization of smeared interfaces, the effect of smear at the pile-rock interface cannot be accurately assessed. This study presents a novel methodology to cast and test small-scale rock-socketed piles with 3D smeared pile-rock interfaces using in situ X-ray computed tomography (CT) imaging. A new smear casting apparatus has been designed to incorporate desired smear fabrics distribution around the model piles comprising idealized saw-tooth asperities. Different materials were trialed to represent the smeared interfaces and the most suitable one for this study was chosen to be a mixture of petroleum jelly and kaolin through the evaluation of the load-displacement behavior and the X-ray CT images. Various smear configurations were cast on the leading faces of the pile asperities (smear-dominant, balanced rock-smear, and rock-dominant) and their placement and volume were compared with the design values to provide confidence in the proposed experimental methodology. Moreover, the micromechanics evolving at the fully smeared leading-faced interface were assessed in detail using the vertical load-displacement behavior and the corresponding X-ray CT images acquired during multi-stage in situ loading. Based on the observations, the interface mechanics for the smeared shafts were classified into smear compression, subsequent smear compression with shearing, and rock shearing. The proposed experimental methodology opens new avenues for studying the smear fabric effect on the load-bearing mechanisms of smeared piles socketed in soft rock.