31 May 2021 in Applied Physics Letters
We report on the demonstration of ferroelectricity in ScxAl1-xN grown by molecular beam epitaxy on GaN templates. Distinct polarization switching is unambiguously observed for ScxAl1-xN films with Sc contents in the range of 0.14–0.36. Sc0.20Al0.80N, which is nearly lattice-matched with GaN, exhibiting a coercive field of ∼ 4.2 MV/cm at 10 kHz and a remnant polarization of ∼135 μC/cm2. After electrical poling, Sc0.20Al0.80N presents a polarization retention time beyond 105 s. No obvious fatigue behavior can be found with up to 3 × 105 switching cycles. The work reported here is more than a technical achievement. The realization of ferroelectric single-crystalline III–V semiconductors by molecular beam epitaxy promises a thickness scaling into the nanometer regime and makes it possible to integrate high-performance ferroelectric functionality with well-established semiconductor platforms for a broad range of electronic, optoelectronic, and photonic device applications.
11 March 2021 in ACS Applied Materials & Interfaces
21 April 2020 in Journal of Applied Physics
Ferrimagnetic insulators with perpendicular magnetic anisotropy are of particular interest for spintronics due to their ability to mitigate current shunting in spin–orbit torque heterostructures and enable low switching energy, high-density storage magnetic devices. Rare earth iron garnet Tm3Fe5O12 (TmIG) is one such material where prior studies have shown that the negative magnetostriction coefficient and isotropic in-plane tensile strain enable the magnetoelastic anisotropy to overcome the demagnetization energy and stabilize perpendicular magnetic anisotropy. However, the investigation of the tunability of the magnetoelastic anisotropy between thin films that possess perpendicular magnetization and quantification of the magnetoelastic constants has not been reported. Here, we quantify the evolution of magnetic anisotropy in (111)-oriented, epitaxial, 17 nm thick thin films of TmIG using a systematic variation of in-plane epitaxial strain (ranging 0.49%–1.83%) imposed by a suite of commercially available garnet substrates. Within the confines of the imposed strain range and deposition condition, the distortion from cubic symmetry is found to be approximately linear within the in-plane strain. The magnetic anisotropy field can be tuned by a factor of 14 in this strain range. The magnetoelastic anisotropy constant, B2, is found to be approximately constant (∼2500 kJ m−3) and more than 2× larger than the reported bulk value (∼1200 kJ m−3) for a cubic distortion between 90.17° and 90.71°. B2 is found to decrease at cubic distortions of 90.74° and larger. Our results highlight strain engineering, and its limitations, for control of perpendicular magnetic anisotropy.
28 June 2023 in Advanced Materials
Non‐collinear antiferromagnets (AFMs) are an exciting new platform for studying intrinsic spin Hall effects (SHEs), phenomena that arise from the materials’ band structure, Berry phase curvature, and linear response to an external electric field. In contrast to conventional SHE materials, symmetry analysis of non‐collinear antiferromagnets does not forbid non‐zero longitudinal and out‐of‐plane spin currents with polarization and predicts an anisotropy with current orientation to the magnetic lattice. Here, multi‐component out‐of‐plane spin Hall conductivities are reported in L12‐ordered antiferromagnetic PtMn3 thin films that are uniquely generated in the non‐collinear state. The maximum spin torque efficiencies (ξ = JS /Je ≈ 0.3) are significantly larger than in Pt (ξ ≈ 0.1). Additionally, the spin Hall conductivities in the non‐collinear state exhibit the predicted orientation‐dependent anisotropy, opening the possibility for new devices with selectable spin polarization. This work demonstrates symmetry control through the magnetic lattice as a pathway to tailored functionality in magnetoelectronic systems.
30 July 2021 in Microscopy and Microanalysis