Philip John McKeown

Philip John McKeown

Auto-generated profile, based on publicly available information

Philip John McKeown

Plastometrex Ltd. 204 Science Park, Milton Road Cambridge CB4 0GZ UK

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 August 2024 in Advanced Engineering Materials
Verified
Journal Article
Open access
HTHannes Tammpere
Hannes Tammpere
PMPhil McKeown
Phil McKeown
JMJames Miller
James Miller
CFChizhou Fang
Chizhou Fang
ECEmily Curtis
Emily Curtis
BCBill Clyne
Bill Clyne
This is a first report on profilometry‐based indentation plastometry (PIP) at high temperature (HT), covering both thermal characterization and issues for obtaining stress–strain curves. The heating system has a relatively low thermal inertia, reaching 800 °C within about 10 min, while both indentation (≈20 s) and cooling (≈20 min) are also quick. This capability is useful in terms of limiting exposure of the sample to prolonged periods at HT, and hence avoiding the formation of thick oxide layers (which can affect indent profiles and hence inferred stress–strain curves). There is good general consistency between stress–strain curves obtained via HT‐PIP and those from tensile testing. However, the possibility of creep (time‐dependent deformation) affecting the outcomes (of both types of test), particularly at higher temperatures, should be borne in mind. Creep has a characteristic effect on tensile curves, which can often be confirmed and investigated by changing the imposed strain rate. It can also be revealed by carrying out the HT‐PIP testing with different penetration velocities or by monitoring the shape of the load–displacement plot.

7 February 2025 in Advanced Engineering Materials
Verified
Journal Article
Open access
PMPhilip John McKeown
Philip John McKeown
JMJames Rees Miller
James Rees Miller
BCBill Clyne
Bill Clyne
This work concerns the mechanical response of three Ti‐based alloys at room temperature, which is observed to be “creep‐affected” and hence to exhibit a dependence on time (within the “quasi‐static” range of strain rate). They have been tensile tested (over this range of strain rate) and subjected to profilometry‐based indentation plastometry (PIP) with a range of penetration velocities (and hence of effective average strain rate). In addition, they have been creep tested, with different fixed loads (corresponding to nominal stresses in the vicinity of the yield stress). Using the Miller–Norton equation to capture creep strain histories, the outcomes of these tests have been converted so that they correspond to those expected with a fixed true stress. These characteristics have then been used in a simple numerical model of a tensile test, incorporating the effect of creep. Good overall consistency is observed and the procedures described here are thought to have wide potential for the extraction of both plasticity and creep characteristics from a simple series of tensile (or PIP) tests carried out with a range of strain rates.

19 May 2025 in Advanced Engineering Materials
Verified
Journal Article
Open access
JMJames Rees Miller
James Rees Miller
PMPhilip John McKeown
Philip John McKeown
HQHillary Qiu
Hillary Qiu
BCBill Clyne
Bill Clyne
This work concerns the application of profilometry‐based indentation plastometry (PIP) to pure tungsten, at temperatures up to 800 °C. PIP involves extraction of stress–strain curves from measured indent profiles, via (automated) inverse finite‐element method modeling. This metal is brittle at room temperature, but plastic deformation (with little work hardening) becomes prevalent above about 200 °C. PIP‐derived curves are consistent with tensile results in this regime. For lower temperatures, PIP allows extraction of yield stress values and work hardening characteristics, but brittle fracture precludes this for tensile testing. Attention is paid to effects induced by exposure to air at high temperature, with both oxide layer formation and the absorption of oxygen being investigated. At 800 °C, a highly porous oxide rapidly forms, with approximately linear growth kinetics. However, this has little effect on measured indent profiles (and hence on inferred stress–strain curves), both because time at high temperature can be kept short during PIP testing and due to the weak and porous nature of the oxide. A check on the role of creep reveals that it was significant at 800 °C (for typical quasistatic strain rates), but has only a relatively minor effect on the PIP‐inferred stress–strain curve.