Michael J. Wood

Michael J. Wood

Auto-generated profile, based on publicly available information

Michael J. Wood

Department of Chemical Engineering, McGill University , Montreal, Quebec H3A 0C5, Canada

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 April 2021 in Nanomaterials
Verified
Journal Article
Open access
PDF file
MWMichael J. Wood
Michael J. Wood
PSPhillip Servio
Phillip Servio
AKAnne-Marie Kietzig
Anne-Marie Kietzig
In this work, we investigate the fabrication of stainless-steel substrates decorated with laser-induced periodic surface structures (LIPSS) of both hydrophilic and hydrophobic wettability through different post-processing manipulation. In carrying out these experiments, we have found that while a CO2-rich atmosphere during irradiation does not affect final wettability, residence in such an atmosphere after irradiation does indeed increase hydrophobicity. Contrarily, residence in a boiling water bath will instead lead to a hydrophilic surface. Further, our experiments show the importance of removing non-sintered nanoparticles and agglomerates after laser micromachining. If they are not removed, we demonstrate that the nanoparticle agglomerates themselves become hydrophobic, creating a Cassie air-trapping layer on the surface which presents with water contact angles of 180°. However, such a surface lacks robustness; the particles are removed with the contacting water. What is left behind are LIPSS which are integral to the surface and have largely been blocked from reacting with the surrounding atmosphere. The actual surface presents with a water contact angle of approximately 80°. Finally, we show that chemical reactions on these metallic surfaces decorated with only LIPSS are comparatively slower than the reactions on metals irradiated to have hierarchical roughness. This is shown to be an important consideration to achieve the highest degree of hydro-philicity/phobicity possible. For example, repeated contact with water from goniometric measurements over the first 30 days following laser micromachining is shown to reduce the ultimate wettability of the surface to approximately 65°, compared to 135° when the surface is left undisturbed for 30 days.

4 October 2022 in ACS Applied Materials & Interfaces
Verified
Journal Article
Closed access
MWMichael J. Wood
Michael J. Wood
GBGregory Brock
Gregory Brock
JDJuliette Debray
Juliette Debray
PSPhillip Servio
Phillip Servio
AKAnne-Marie Kietzig
Anne-Marie Kietzig

1 June 2020 in Physics of Fluids
Verified
Journal Article
Open access
PDF file
DADamon G. K. Aboud
Damon G. K. Aboud
MWMichael J. Wood
Michael J. Wood
AKAnne-Marie Kietzig
Anne-Marie Kietzig
This report investigates how different splashing mechanisms affect the oblique splash threshold of drops impacting a dry solid surface. The splashing behaviors of water, ethanol, and a water/ethylene glycol solution are observed over a wide range of drop diameters (0.7 mm < D < 2.2 mm) and Weber numbers (10 < We < 1040), and several published models are tested in order to predict the thresholds between deposition, one-sided splashing, and two-sided splashing. We found that the splash threshold of liquids that exhibit the corona splashing mechanism can be readily predicted by existing models. However, for liquids such as water that exhibit prompt splashing, the oblique splash threshold is not successfully predicted by any presently established correlation. Hence, our findings identify a critical knowledge gap in the drop impact field, since the behavior of water is of fundamental importance to countless engineering problems. Finally, combining our own results with others reported in the literature, we address some contradictory reports about the influence of liquid viscosity on the splash threshold and demonstrate that the presence or lack of thin-sheet in different experiments could explain the contradictions present in the literature.

10 August 2022 in ACS Applied Materials & Interfaces
Verified
Journal Article
Closed access
MWMichael J. Wood
Michael J. Wood
GBGregory Brock
Gregory Brock
PSPhillip Servio
Phillip Servio
AKAnne-Marie Kietzig
Anne-Marie Kietzig

29 September 2022 in Colloids and Surfaces A: Physicochemical and Engineering Aspects
Verified
Journal Article
Closed access
MAMohammad Bagher Asadi
Mohammad Bagher Asadi
DADamon G. K. Aboud
Damon G. K. Aboud
MWMichael J. Wood
Michael J. Wood
Gianluca ZeppetelliGianluca Zeppetelli
Gianluca Zeppetelli
AKAnne-Marie Kietzig
Anne-Marie Kietzig

1 February 2018 in Physics of Fluids
Verified
Journal Article
Closed access
PDF file
MWMichael J. Wood
Michael J. Wood
FAFelipe Aristizabal
Felipe Aristizabal
MCMatthew Coady
Matthew Coady
KNKent Nielson
Kent Nielson
PRPaul J. Ragogna
Paul J. Ragogna
AKAnne-Marie Kietzig
Anne-Marie Kietzig
The production of millimetric liquid droplets has importance in a wide range of applications both in the laboratory and industrially. As such, much effort has been put forth to devise methods to generate these droplets on command in a manner which results in high diameter accuracy and precision, well-defined trajectories followed by successive droplets and low oscillations in droplet shape throughout their descents. None of the currently employed methods of millimetric droplet generation described in the literature adequately addresses all of these desired droplet characteristics. The reported methods invariably involve the cohesive separation of the desired volume of liquid from the bulk supply in the same step that separates the single droplet from the solid generator. We have devised a droplet generation device which separates the desired volume of liquid within a tee-apparatus in a step prior to the generation of the droplet which has yielded both high accuracy and precision of the diameters of the final droplets produced. Further, we have engineered a generating tip with extreme antiwetting properties which has resulted in reduced adhesion forces between the liquid droplet and the solid tip. This has yielded the ability to produce droplets of low mass without necessitating different diameter generating tips or the addition of surfactants to the liquid, well-defined droplet trajectories, and low oscillations in droplet volume. The trajectories and oscillations of the droplets produced have been assessed and presented quantitatively in a manner that has been lacking in the current literature.