5 November 2012 in Journal of Intelligent Material Systems and Structures
The focuses of this study are to design an adaptive-tuned vibration absorber based on a smart materials known as magnetorheological elastomers and to test its dynamic performance. A primary system replicating a miniature cryogenic cooler (i.e. mass and shape) was designed and fabricated in order to test the effectiveness of the vibration absorber. A hybrid magnetic system (electromagnet and permanent magnets) was also designed and fabricated in order to actuate the magnetorheological elastomers as an adaptive stiffness element in the vibration absorber. The vibration testing was conducted on both the primary system and vibration absorber individually in order to characterize the behavior and verify the design constraints. Further testing was performed on a 2-degrees-of-freedom system to measure and assess the feasibility of the magnetorheological elastomer material for use in an application requiring an adaptive vibration absorber. The results show that by using a hybrid design for the electromagnet within the vibration absorber, the stiffness of the magnetorheological elastomer material can be increased and decreased above its nominal value, therefore demonstrating the feasibility of this design as an alternative adaptive vibration absorber.
24 May 2005 in Journal of Vibration and Acoustics
This paper offers an experimental robustness analysis of a semi-active tuned vibration absorber (TVA) subject to structural mass off-tuning, which occurs frequently in practical applications of TVAs. One of the critical problems of a conventional TVA is off-tuning or miss-tuning because off-tuned TVAs may amplify the vibrations of the primary structure. This study intends to evaluate how well semi-active TVAs are able to adapt to structural mass changes (mass off-tuning) as compared with passive TVAs. To this end, a test apparatus was built to represent a two-degree-of-freedom structure model coupled with a TVA. The semi-active TVA considered in this study employed a magneto-rheological (MR) damper as its damping element to enhance overall performance. Using this test apparatus, a series of tests were conducted to identify the optimal tuning parameters of the TVAs. After obtaining each TVA’s optimal tuning parameters based on equal peak transmissibility criteria, the mass off-tuning tests were then performed on the optimally tuned TVAs. In order to off-tune the system, the mass of the primary structure varied from to of its nominal mass using a set of steel plates. Overall, the experimental results show that the semi-active MR TVA outperforms the passive TVA in reducing maximum vibrations. Moreover, the results show that the semi- active TVA is more robust to changes in the primary mass (mass off-tuning) The results further show that the semi-active MR TVA offers larger performance gains as the structure mass increases.
24 January 2005 in Shock and Vibration
A conventional passive tuned vibration absorber (TVA) is effective when it is precisely tuned to the frequency of a vibration mode; otherwise, it may amplify the vibrations of the primary system. In many applications, the frequency often changes over time. For example, adding or subtracting external mass on the existing primary system results in changes in the system’s natural frequency. The frequency changes of the primary system can significantly degrade the performance of TVA. To cope with this problem, many alternative TVAs (such as semiactive, adaptive, and active TVAs) have been studied. As another alternative, this paper investigates the use of Shape Memory Alloys (SMAs) in passive TVAs in order to improve the robustness of the TVAs subject to mass change in the primary system. The proposed SMA‐TVA employs SMA wires, which exhibit variable stiffness, as the spring element of the TVA. This allows us to tune effective stiffness of the TVA to adapt to the changes in the primary system′s natural frequency. The simulation model, presented in this paper, contains the dynamics of the TVA along with the SMA wire model that includes phase transformation, heat transfer, and the constitutive relations. Additionally, a PID controller is included for regulating the applied voltage to the SMA wires in order to maintain the desired stiffness. The robustness analysis is then performed on both the SMA‐TVA and the equivalent passive TVA. For our robustness analysis, the mass of the primary system is varied by ± 30% of its nominal mass. The simulation results show that the SMA‐TVA is more robust than the equivalent passive TVA in reducing peak vibrations in the primary system subject to change of its mass.
1 February 2009 in Journal of Physics: Conference Series
The primary goal of this paper is to characterize and model the compression properties of Magneto-Rheological Elastomers (MREs). MRE samples were fabricated by curing a two component elastomer resin with 30 % content of 10 μm sized iron particles by volume. In order to vary the magnetic field during compressive testing, a test fixture was designed and fabricated in which two permanent magnets could be variably positioned on either side of the specimen. By changing the distance between the magnets, the fixture allowed for varying the magnetic field that passes uniformly through the sample. Using this test setup and a dynamic test frame, a series of compression tests of MRE samples was performed by varying the magnetic field and frequency of loading. The results show the MR effect (percent increase in the materials "stiffness") increases as the magnetic field increases and loading frequency increases within the range of the magnetic field and input frequency considered in this study. Furthermore, a phenomenological model was developed to capture the dynamic behaviours of the MREs under compression loadings.
5 June 2009 in Journal of Vibration and Acoustics
This paper presents a new semi-active control scheme that can reduce the unbalance responses in a flexible rotor system with multiple masses (i.e., disks) using a magnetorheological fluid based squeeze film damper (MR-SFD). The proposed control scheme is designed to effectively attenuate multiple vibration modes of the rotor system. The control algorithm begins with the determination of the optimal location of the MR squeeze film damper to maximize its control performance over several flexural critical speeds of interest. After identifying the optimal position of the damper based on the structure dynamics modification method, the singular value analysis was performed, with varying rotor speed, to determine the scheduled input current to the MR squeeze film damper at each rotational speed. Using a rotor-bearing model coupled with three disks and a MR-SFD, a series of numerical simulations was performed to evaluate the effectiveness of the control algorithm. In addition to the numerical study, a test rotor system (equivalent to the numerical model) and a prototype MR squeeze film damper were constructed and tested to experimentally evaluate the performance of the prototype with the control and validate the simulation results. The numerical and test results indicate that optimal positioning of the damper alone (without implementing the control) significantly reduced the unbalance responses of the disks near the first critical speed. Activating the controller, the damper further attenuated the unbalanced vibrations of the rotor system at the second critical speed. The results show that, at this critical speed, the peak vibration magnitudes of the disks were attenuated by nearly 70%.
1 October 2003 in The Journal of the Acoustical Society of America