Petrology, Volcanology, and Geochemistry Research Group, Faculty of Earth Sciences and Technology, Bandung Institute of Technology (ITB), Bandung, West Java 40132, Indonesia
Auto-generated profile, based on publicly available information
Prihadi Sumintadireja
Petrology, Volcanology, and Geochemistry Research Group, Faculty of Earth Sciences and Technology, Bandung Institute of Technology (ITB), Bandung, West Java 40132, Indonesia
In recent years, dozen low-intensity earthquakes occurred in southern Garut, West Java Indonesia; two of them were reported destructive. However, those shallow earthquake clusters are hardly associated with well-known active faults in the area. Hence, we conducted 3D gravity combined with 2D magnetotellurics (MT) inversions to study the subsurface. Gravity and MT modeling confirm a basin with around 5 km depth consisting of two subbasins separated by a NE-SW trending local-high ridge. The local high coincides with the magmatic intrusion in geothermal fields and aligns with a series of volcanic bodies’ lineament observed on the surface. We interpret this structural high as a preexisting fault that serves as a magma pathway in the tectonomagmatic interaction. Shallow low-magnitude seismicity in the southern Garut area tends to occur in the resistive bodies. We interpret that heat from the cooling magmatic intrusion may decrease the effective fault-normal stress of the rocks, leading to a decrease in fault failure resistance and may initiate rupture. The resistivity structure around the initial rupture may affect whether or not the nucleation will end up as a large-magnitude earthquake. Furthermore, the unconsolidated young volcanic cover in this area could amplify ground shaking when earthquake occurs that might lead to more extensive damage.
24 April 2017 in IOP Conference Series: Earth and Environmental Science
Controlled-Source Audio-frequency Magnetotellurics (CSAMT) is a frequency domain sounding technique employing typically a grounded electric dipole as the primary electromagnetic (EM) source to infer the subsurface resistivity distribution. The use of an artificial source provides coherent signals with higher signal-to-noise ratio and overcomes the problems with randomness and fluctuation of the natural EM fields used in MT. However, being an extension of MT, the CSAMT data still uses apparent resistivity and phase for data representation. The finite transmitter-receiver distance in CSAMT leads to a somewhat "distorted" response of the subsurface compared to MT data. We propose a simple technique to present CSAMT data as an apparent resistivity pseudo-section with more meaningful information for qualitative interpretation. Tests with synthetic and field CSAMT data showed that the simple technique is valid only for sounding curves exhibiting a transition from high – low – high resistivity (i.e. H-type) prevailing in data from a geothermal prospect. For quantitative interpretation, we recommend the use of the full-solution of CSAMT modelling since our technique is not valid for more general cases.
24 December 2025 in RISET Geologi dan Pertambangan
The debris flow can be modeled as non-Newtonian flow using physical and mathematical modeling methods based on rheological property measurements and movement parameters. The numerical simulation in this research used smoothed particle hydrodynamics (SPH) to solve the momentum and energy equations. The debris flow modeled in this research is located in the Bentarsari Basin, which is surrounded by hills composed of volcanic breccia from the Kumbang Formation (Tpk) and tends to be more susceptible to landslides and may become debris flows. The results of the numerical simulation begin with the collapse of the natural dam and become debris flow with 8.8 m maximum thickness. The debris flow destroyed the bridge in the 40s with 100 kPa pressure. A speed of 6 m/s was reached at 120 s. A small hill in the deposition area was hit by debris flow at 130 s causing 18 casualties. The debris flow enters the deposition area at the 150 s. The debris flow average velocity shows relatively transverse pattern (1-126 s), constant pattern (126-289 s), and random pattern (after 289 s). The debris flow average pressure shows steep negative gradient pattern (1-47 s) and relatively flat pattern (after 47 s). The average debris flow thickness shows a steep negative gradient pattern (1-13 s) and a gentle negative gradient pattern (after 13 s). The results of debris flow modeling using SPH can simulate the debris flow segregation process, which usually cannot be captured by conventional debris flow modeling software.