14 May 2024 in IEEE Transactions on Industrial Electronics
Despite the merit of fast dynamics, deadbeat predictive current control (DPCC) suffers from the dc and ac disturbances. To address the issue, active disturbance rejection control (ADRC) has been proposed, including the conventional and composite ADRC schemes. However, the conventional ADRC cannot suppress the ac disturbance effectively. While in the composite ADRC, the performances of the current control and disturbance suppression loops are coupled, distorting the deadbeat properties of the DPCC. In addition, both schemes are subject to weak capability in tracking the fast time-varying disturbance. To solve the problems, this article proposes a decoupled ADRC based on the composite disturbance observer, where the second-order disturbance extended state observer (SDESO) and quasi-resonant controller (QRC) are employed to suppress the dc and ac disturbances, respectively. Compared with the composite ADRC, the proposed scheme can fully decouple the performances of the current control and disturbance suppression loops, and thus deadbeat properties can be retained. In addition, by the SDESO, the proposed scheme enables superior dynamic performance in tracking the time-varying disturbance. The system stability and anti-disturbance capability of the proposed scheme are analyzed in detail. Finally, the effectiveness of the proposed scheme is validated on a 0.55kWPMSM platform.
18 October 2022 in IEEE Transactions on Industrial Electronics
A deadbeat-direct torque and flux control (DB-DTFC) for brushless axial-flux magnetic-geared double-rotor machines (AMGDRMs) is presented in this article. The AMGDRM is employed as a power-splitting component in hybrid electric vehicles to enable speed decoupling between the internal combustion engine (ICE) and load. Since the rigid connection between the ICE and the drive train is replaced by the AMGDRM, fast torque control of the AMGDRM is required for the ICE speed regulation. Furthermore, the ICE torque contains abundant harmonics, inevitable sinusoidal components are introduced to the modulating rotor torque for torque balance, and further to the PM rotor torque owing to the magnetic-gear effect. Since both the PM rotor of the AMGDRM and the traction motor contribute to the hybrid electric system total torque output (i.e., torque coupling), the cascaded traction motor should compensate the PM rotor torque ripple actively to guarantee smooth total output torque. However, proportional-integral (PI) regulator suffers from limited bandwidth and thus could not realize accurate torque decoupling. Therefore, DB-DTFC, where torque and flux linkage are decoupled and respectively achieve their reference commands within two sampling periods, i.e., deadbeat responses, is proposed to enable a faster and more robust ICE speed control and accurate torque decoupling. The DB-DTFC law is derived and discrete-time close-loop current and flux linkage observers of the AMGDRM are developed. The proposed scheme and its superiorities are experimentally validated on an AMGDRM prototype test bench.
11 September 2024 in IEEE Transactions on Power Electronics
This article presents a decoupled dead-time compensation method for voltage source inverters in permanent magnet synchronous machine (PMSM) drives. In the proportional-integral-resonant (PIR) based compensation scheme, the performances of the current control loop and dead-time compensation are coupled. Hence, effective compensation of the dead-time effect is yield with the expense of distorted current step response, where significant overshoot and oscillation are introduced. Besides, the extended-state observer (ESO) based scheme suffers from poor compensation capability due to limited tracking bandwidth. To increase the tracking bandwidth, the quasi-resonant-controller (QRC) based disturbance observer was proposed. However, such observer suffers from the problem of system instability. To address above issues, a revised-resonant control-based disturbance observer is proposed in this article, which could fully decouple the performances of the current control loop and dead-time compensation. Compared with the PIR, the proposed scheme could donate superior compensation capability without introducing overshoot and oscillation in the current step response. Compared with the ESO, the proposed scheme could increase tracking bandwidth and thus donate superior compensation capability. Compared with the QRC-based observer, the proposed scheme could guarantee system stability. Detailed analysis of system stability and compensation capability is presented. Finally, the proposed scheme is experimentally validated on a 0.55 kW PMSM platform.
10 May 2021 in IEEE Transactions on Magnetics
Axial-flux magnetic-geared double-rotor machines (AMGDRMs) are characterized as a potential key component of the power-splitting system in hybrid electric vehicles (HEVs), but its conventional configuration suffers from the high axial magnetic force. In this article, an interior-modulating-rotor AMGDRM (IMR-AMGDRM) is proposed to solve this problem. To reduce computation burden, an analytical model of the IMR-AMGDRM is proposed based on the subdomain method. The analytical expressions of the magnetic field distribution and electromagnetic performances, such as torque and axial force, are developed. Finally, the results of the proposed analytical model are compared with those of the 3-D finite element analysis (FEA). The influences of the geometrical parameters of the ferromagnetic pole pieces and permanent magnets (PMs) are also investigated by the analytical model and 3-D FEA. The accuracy and the cause of the calculation error of the analytical model are studied.
4 December 2023 in IEEE Transactions on Energy Conversion
As a compound structure machine, dual-winding dual-flux-concentrated magnetic-field-modulated brushless compound-structure machine (DDMFM-BCSM) could achieve function of magnetic-field modulated brushless double-rotor machine (MFM-BDRM) and permanent magnet synchronous machine (PMSM) at the same time, which means it could be applied to replace the combination of planetary gears and motors in hybrid electric vehicles (HEVs). Finite element method (FEM) could realize accurate analysis of DDMFM-BCSM while it has disadvantage of complex modeling and long computing time. To achieve fast analysis and design of DDMFM-BCSM, equivalent magnetic network (EMN) model is built in this paper. After meshing of each component, radial and tangential reluctance and magnetomotive force (MMF) could be obtained. Then EMN model could be analyzed by solving EMN equation system. Based on magnetic flux distribution from EMN model, performance of DDMFM-BCSM, including flux density, flux linkage, back EMF, torque and power factor, could be calculated. Comparison shows that result of EMN model is in good agreement with that of FEM. Finally, a DDMFM-BCSM prototype is manufactured and tested.
15 September 2021 in IEEE Transactions on Industrial Electronics
As a promising candidate of the electrical continuously variable transmission, the integrated magnetic-field-modulated brushless compound-structure machine (IMFM-BCSM) has advantages of compact structure and no brush. The IMFM-BCSM is composed of a stator with two sets of windings, a permanent-magnet (PM) rotor and a modulation rotor. Due to its special operating principle, i.e., the magnetic field modulation principle, the back electromotive force (EMF) waveform distortion of the IMFM-BCSM is more serious than that of the conventional PM machine. To solve the above problem, a quasi-sinusoidal concentrated winding (QSCW) configuration is proposed and corresponding design method is further introduced. In order to observe the “filtering ability” of the QSCW, comparisons between QSCW configuration and fractional-slot concentrated winding configuration are carried out. The results show that when the QSCW configuration is employed, the no-load back EMF of the regular winding is more sinusoidal; the distortion degree is less affected by the rotor speeds; and the torque ripple is much smaller. Finally, a prototype is manufactured to verify the theoretical analysis.