Francisco Jose del Campo Melchor

Francisco Jose del Campo Melchor

Auto-generated profile, based on publicly available information

Francisco Jose del Campo Melchor

Mechanical and Aerospace Engineering Department, University of California, Los Angeles (UCLA), Los Angeles, California 90095, USA

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 April 2023 in Journal of Fluid Mechanics
Verified
Journal Article
Open access
PDF file
NYNing Yu
Ning Yu
ZLZhaohui “Ray” Li
Zhaohui “Ray” Li
AMAlexander McClelland
Alexander McClelland
FMFrancisco Jose del Campo Melchor
Francisco Jose del Campo Melchor
SLSun Youb Lee
Sun Youb Lee
CKChang-Jin Kim
Chang-Jin Kim
This paper studies the sustainability of plastrons on superhydrophobic (SHPo) surfaces made of longitudinal micro-trenches covered by nano-grass with the main interest on hydrodynamic friction drag reduction in high-speed flows of open water, which represent the operating conditions of common watercraft. After revising the shear-driven drainage model to address the air diffusion for SHPo surfaces, the existing theories are combined to reveal the trends of how the immersion depth, air saturation level and shear stress affect the maximum attainable plastron length. Deviations from the theories by the dynamic effect at the two ends of the trench, the interfacial contaminations and turbulent fluctuation are also discussed. A combinatorial series of well-defined SHPo trench surfaces (4 cm × 7 cm in size with varying trench widths, depths, lengths and roughnesses) is microfabricated and attached underneath a 4 m long motorboat on seawater in turbulent flows up to 7.2 m s−1(shear rate ∼83 000 s−1and friction Reynolds number ∼5500). Because the plastron can provide a substantial slip only while its air–water interfaces are pinned (or only slightly depinned) at the trench top, two underwater cameras are employed to differentiate the pinned (and slightly depinned) interfaces from the depinned (and no) interfaces. In addition to achieving pinned plastrons on 6 cm long trenches aligned to high-speed flows in open water, the experimental results corroborate the theoretical estimations, supporting the design of SHPo surfaces for field applications.

12 November 2024 in Flow
Verified
Journal Article
Open access
PDF file
NYNing Yu
Ning Yu
FMFrancisco Jose del Campo Melchor
Francisco Jose del Campo Melchor
ZLZhaohui “Ray” Li
Zhaohui “Ray” Li
JJJihun Jeon
Jihun Jeon
JEJeff D. Eldredge
Jeff D. Eldredge
CKChang-Jin Kim
Chang-Jin Kim
Superhydrophobic (SHPo) surfaces can capture a thin layer of air called a plastron under water to reduce skin friction. Although a ~30 % drag reduction has been recently reported with longitudinal micro-trench SHPo surfaces under a boat and in a towing tank, the results lacked the consistency to establish a clear trend. Designed based on Yu et al. (J. Fluid Mech, vol. 962, 2023, A9), this work develops and tests a series of high-performance SHPo surface coupons that can sustain a pinned plastron underneath a passenger motorboat revamped to reach 14 knots. Importantly, plastrons in a pinned state, not just their existence, are confirmed during flow experiments for the first time. All the drag-reduction data measured on different longitudinal micro-trenches are found to collapse if plotted against slip length in wall units. In comparison, aligned posts and transverse trenches show less and little drag reduction, respectively, confirming the adverse effect of the spanwise slip in turbulent flows. This report not only verifies SHPo surfaces can provide a consistent drag reduction at high speeds in open sea but also shows that one may predict the amount of drag reduction in turbulent flows using the physical slip length obtained for Stokes flows.

30 September 2026 in Experiments in Fluids
Verified
Journal Article
Open access
PDF file
ECEric Hyunsung Cho
Eric Hyunsung Cho
ZLZhaohui Ray Li
Zhaohui Ray Li
JJJihun Jeon
Jihun Jeon
MBMatthew Bross
Matthew Bross
WSWilliam A. Straka
William A. Straka
CKChang-Jin Kim
Chang-Jin Kim
Reduction of frictional drag is examined on a 31 cm × 15 cm flat plate covered with superhydrophobic (SHPo) longitudinal microtrenches in a high-speed water tunnel capable of imposing wall shear levels representative of operating water vessels. Experimentation capable of testing substantially larger (~ 16× larger in area than before) microtrench-array surfaces in a large, high-speed water tunnel using a standard measurement method is developed, thereby providing high-quality, rigorously controlled experimental data to support and validate turbulent SHPo drag reduction. High-performance microtrench surfaces featuring hierarchical roughness and re-entrant trench tops are microfabricated on silicon wafers, diced into 7.6 cm × 4.7 cm tiles, and assembled as a 4 × 3 array on the drag plate interfaced with a drag balance for shear-drag measurement. The water tunnel enables control of water pressure and air saturation and allows a low-grazing-angle view for detecting plastron depinning. Two microtrench geometries are tested: (i) 50 µm pitch, 90% gas fraction, 100 µm depth, and 10 mm length, designed primarily for plastron stability and (ii) 100 µm pitch, 92% gas fraction, 200 µm depth, and 20 mm length for larger slip. The former geometry achieves around 30% drag reductions at flow speeds corresponding to a wall shear stress of about 100 Pa, surpassing the previous record of 70 Pa and reaching conditions relevant to practical vessel operation. Graphical abstract