Nicola Y. Bailey

Nicola Y. Bailey

Auto-generated profile, based on publicly available information

Nicola Y. Bailey

University of Bath

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2022 in Physics of Fluids
Verified
Journal Article
Open access
PDF file
NBNicola Y. Bailey
Nicola Y. Bailey
JOJ. Michael Owen
J. Michael Owen
IMIsaac F. Mear
Isaac F. Mear
HTHui Tang
Hui Tang
A robust and fully predictive mathematical representation has been derived to predict the swirl ratio, pressure, and torque in enclosed rotor–stator cavities. For the flow regime of interest, turbulent boundary layers form on the rotor and stator, between which there is an inviscid fluid core. Utilizing the momentum-integral equations with suitable assumptions and the continuity of mass equation, governing equations are derived for the flow behavior, with the assumption that the swirl ratio is dependent on the radius. Predictive initial conditions are formulated, and a robust, computationally inexpensive numerical technique is implemented and predictions are shown to be in reasonable agreement with existing experimental data. The swirl ratio was proven to be highly dependent on the radius, with the distribution modified by the shroud and hub conditions. Additionally, the effects of two geometrical parameters were studied, namely, the gap ratio and non-dimensional inner radius. As the gap ratio increases from 0.05 to 0.5, the swirl ratio at the outer radius decreases from 0.56 to 0.35, leading to an increase in torque coefficient from 0.38 to 0.44. The swirl ratios for different inner radii differ at the inner part of the cavity while converging to a single value at the outer radius. The presented model can easily be integrated into the design code for gas turbine engines, contributing to the design of more efficient engines.

23 May 2015 in Journal of Engineering Mathematics
Verified
Journal Article
Open access
PDF file
NBN. Y. Bailey
N. Y. Bailey
KCK. A. Cliffe
K. A. Cliffe
SHS. Hibberd
S. Hibberd
HHenry Power
Henry Power
A modified Reynolds equation for flow dynamically represented as incompressible is used to model the dynamics of a thin film bearing with slip flow and a rapidly rotating coned rotor. Previous studies including a Navier slip length shear condition on the bearing faces are extended to investigate applications with a coned bearing gap. A modified Reynolds equation for the film flow is coupled, through the pressure exerted by the fluid film, to the dynamic motion of the stator. Introducing a new variable leads to explicit analytical expressions for the pressure field and force on the stator with the equation for the time-dependent face clearance transformed to a nonlinear second-order non-autonomous ordinary differential equation. The face clearance for periodic axial motion of the coned rotor is obtained using a stroboscopic map solver; a focus is investigating bearing behaviour under extreme conditions. The coupled fluid flow and unsteady bearing dynamics are examined for a range of configurations to evaluate potential face contact over a range of bearing surface conditions.

28 March 2017 in Journal of Fluid Mechanics
Verified
Journal Article
Closed access
PDF file
NBN. Y. Bailey
N. Y. Bailey
SHS. Hibberd
S. Hibberd
HHenry Power
Henry Power
A gas lubricated bearing model is derived which is appropriate for a very small bearing face separation by including velocity slip boundary conditions and centrifugal inertia effects. The bearing dynamics is examined when an external harmonic force is imposed on the bearing due to the bearing being situated within a larger complex dynamical system. A compressible Reynolds equation is formulated for the gas film which is coupled to the bearing structure through an axial force balance where the rotor and stator correspond to spring–mass–damper systems. Surface slip boundary conditions are derived on the bearing faces, characterised by the slip length parameter. The coupled bearing system is analysed using a stroboscopic map solver with the modified Reynolds equation and structural equations solved simultaneously. For a sufficiently large forcing amplitude a flapping motion of the bearing faces is induced when the rotor and stator are in close proximity. The minimum bearing gap over the time period of the external forcing is examined for a range of bearing parameters.

2 December 2024 in PLOS ONE
Verified
Journal Article
Open access
PDF file
SWSam Walters
Sam Walters
BMBenjamin Metcalfe
Benjamin Metcalfe
MTMartin Twiste
Martin Twiste
ESElena Seminati
Elena Seminati
NBNicola Y Bailey
Nicola Y Bailey
Monitoring the volume and shape of residual limbs post-amputation is necessary to achieve optimal socket fit and determine overall limb health, yet contemporary clinical measurement techniques show high variance between measures. Three-dimensional scanning presents an opportunity for improved accuracy and reliability of residual limb measurements, however, three-dimensional scanners remain prohibitively expensive. A cost-effective alternative is the use of software that can utilise the photographs of modern smartphone cameras to create geometrically accurate scans. Whilst several studies have investigated the potential of privately developed photogrammetry algorithms for capturing residual limbs with clinical accuracy, none to the authors knowledge have explored commercially available software to do the same. Three applications were tested, namely Polycam, Luma, and Meshroom, to determine if they could produce clinically acceptable results. Scans of ten residual limbs were created using both smartphone technology and a reference structured-light scanner (Artec EVA), against which the validity and reliability of the resulting limb models were assessed using the Bland-Altman method and Intraclass Correlation Coefficient, respectively. Polycam and Luma achieved both Pearson Coefficients and Intraclass Correlation Coefficients of 0.999, and Coefficients of Variation of 1.1% and 1.4%, respectively. Volume reliability coefficients were 58.3 ml and 70.0 ml respectively for Polycam and Luma, whereas Meshroom failed to meet any of the criteria for clinical suitability, with a repeatability coefficient of 790.3 ml. Both Polycam and Luma exhibit sufficient accuracy and reliability to be considered for clinical volume measurements.

4 December 2014 in IMA Journal of Applied Mathematics
Verified
Journal Article
Open access
PDF file
NBN.Y. Bailey
N.Y. Bailey
KCK.A. Cliffe
K.A. Cliffe
SHS. Hibberd
S. Hibberd
HPH. Power
H. Power
An incompressible fluid flow model for a thin-film thrust bearing with slip flow is derived, leading to a modified Reynolds equation for a highly rotating rotor that incorporates a slip length shear condition on the bearing faces, extending previous bearing studies for new bearing applications associated with decreasing film thickness. Mathematical and numerical modelling is applied to the coupled process of the pressurized fluid flow through the bearing, with a Navier slip condition replacing a no-slip condition, and the axial motion of the rotor and stator. The derived modified Reynolds equation is coupled with the dynamic motion of the stator through the pressure exerted by the fluid film, with explicit analytical expressions for the pressure and force determined and the equation for the bearing gap reduced to a non-linear second-order non-autonomous ordinary differential equation. A mapping solver is used to investigate the time-dependent bearing gap for prescribed periodic motion of the rotor. A parametric study focuses on bearing operation under close contact motion to examine the minimum film thickness and possibility of bearing face contact.

5 February 2013 in IMA Journal of Applied Mathematics
Verified
Journal Article
Closed access
PDF file
NBN. Y. Bailey
N. Y. Bailey
KCK. A. Cliffe
K. A. Cliffe
SHS. Hibberd
S. Hibberd
HHenry Power
Henry Power
An incompressible air-flow model for a fluid film bearing is derived using a modified Reynolds equation for the thin-film dynamics of a rapidly rotating rotor and stator. Mathematical and numerical modelling is applied to the coupled processes of the fluid flow through the bearing and the axial motion of the rotor and stator. This work focuses on extending previous studies to incorporate the dynamics of a coned rotor operating at high speeds and an incompressible lubrication approximation. The dynamics of fully coupled, unsteady bearing motion and associated forcing of the rotor with axial periodic oscillations are studied. The axial motion of the stator is modelled as a spring–mass–damper system that responds to the rotor displacement through the film dynamics. In order to solve the modified Reynolds equation and stator equation simultaneously, a new variable is introduced, namely the time-dependent face clearance. This leads to explicit analytical expressions for the pressure and force in terms of the face clearance and the stator equation is transformed to a non-linear, second-order, non-autonomous, ordinary differential equation for the face clearance. Applying a transient solver gives solutions settling down to a stable periodic behaviour which motivates seeking a solver for periodic solutions. A Fourier spectral collocation scheme is derived to compute the periodic time-dependent face clearance. Both solvers have matching periodic solutions of O(1) with an absolute error of order of magnitude 10−5. The dynamics of the unsteady bearing are examined for a range of pressure gradients and configurations including an asymptotic investigation of small face clearance associated with a start-up transient. Results are provided relating to changes in the width of the bearing, strength of the spring holding stator to its housing, damping of the stator and strength of the force coupling and rotor mass. The dynamics of the bearing are also investigated relative to values of key system parameters including the coning of the rotor, rotation speed and value of the bearing squeeze number. A parameter investigation is undertaken to highlight ideal bearing configurations to maximize the load-carrying capacity, fluid stiffness and damping.