30 December 2020 in Robotics and Technical Cybernetics
This paper presents development of pressure sensor array with capacitance-type unit sensors, with scalable number of cells. Different assemblies of unit pressure sensors and their arrays were considered, their characteristics and fabrication methods were investigated. The structure of primary pressure transducer (PPT) array was presented; its operating principle of array was illustrated, calculated reference ratios were derived. The interface circuit, allowing to transform the changes in the primary transducer capacitance into voltage level variations, was proposed. A prototype sensor was implemented; the dependency of output signal power from the applied force was empirically obtained. In the range under 30 N it exhibited a linear pattern. The sensitivity of the array cells to the applied pressure is in the range 134.56..160.35. The measured drift of the output signals from the array cells after 10,000 loading cycles was 1.39%. For developed prototype of the pressure sensor array, based on the experimental data, the average signal-to-noise ratio over the cells was calculated, and equaled 63.47 dB. The proposed prototype was fabricated of easily available materials. It is relatively inexpensive and requires no fine-tuning of each individual cell. Capacitance-type operation type, compared to piezoresistive one, ensures greater stability of the output signal. The scalability and adjustability of cell parameters are achieved with layered sensor structure. The pressure sensor array, presented in this paper, can be utilized in various robotic systems.
1 August 2021 in Вестник ВГУ. Серия: Системный анализ и информационные технологии
В работе проведен анализ автономных робототехнических систем и разработана классификация, в которой установлены взаимосвязи между массогабаритными характеристиками, энергопотреблением и энергоемкостью источника питания рассмотренных систем. Рассмотрены существующие классификации робототехнических систем и выявлено, что большинство работ посвящены классификациям форм, свойствам и назначению роботов, а также факторам, влияющим на потребление энергии. Анализ и классификация автономных робототехнических средств по уровню потребления энергии позволит осуществлять обоснованный подбор наиболее эффективного класса и уровня мощности беспроводной системы передачи энергии для конкретного робота на этапе проектирования в зависимости от массогабаритных характеристик. Задача является особенно актуальной для активно развивающегося в настоящее время направления беспроводных систем передачи энергии мобильным роботам. В настоящем анализе основное внимание уделяется рассмотрению автономных мобильных наземных роботов, предназначенных для работы в помещениях. Рассмотрены роботы следующих типов: колесные, шагающие, антропоморфные и гибридные, включающие в себя несколько типов конструкций. Анализируемыми параметрами являются: потребляемая мощность, массогабаритные характеристики робота, используемый источник питания и его энергетические характеристики. Выделены четыре группы робототехнических систем по потребляемой мощности: потребители малой мощности (до 10 Вт), средней (от 10 до 250 Вт), высокой (от 250 до 1000 Вт) и сверхвысокой мощности (более 1000 Вт). Определены диапазоны потребляемых мощностей, линейных размеров, массы и энергоемкостей аккумуляторных батарей робототехнических средств для каждой из перечисленных групп. Построены графики зависимости потребляемой мощности от массогабаритных показателей рассмотренных роботов.
30 September 2021 in Robotics and Technical Cybernetics
This paper presents the development of a medium-power wireless power transmission system for use in robotics and other applications. The presented system can be used to power devices or charge batteries. The system is based on the principle of inductive power transmission. A feature of the system is the use of a resonant self-oscillator, for which the transmitting LC circuit of the system is a frequency setting. The use of identical receiving and transmitting resonant circuits makes it possible to refuse additional frequency control devices in the receiving part of the system. The presented circuitry solution of the wireless power transmission system ensures operation in the resonance mode in the receiving and transmitting circuits, where the receiving and transmitting coils are at various positions relative each other, while not requiring a dedicated monitoring and control system for this. Experimental verification of the proposed solution was carried out on a prototype of a system with shell elements, shielding from magnetic fields, while the maximum level of efficiency of the system without an output stabilizer in the receiving part was 80.41%, with a transmitted power of 131.5 W, at a transmission distance of 15 mm. The dependency curves of the efficiency and the transmitted power were obtained for three distances of energy transfer — 0 mm, 15 mm and 30 mm. With distances between the coils up to 30 mm, the efficiency of the system is above 70% with a transmitted power of more than 55 W. Key words Wireless charging system, wireless power transmission, resonant oscillator, wireless power transmission efficiency. Acknowledgements This research is supported by the RFBR, project no.19-08-01215_А.