24 April 2020 in RSC Advances
Gut microbiota plays an important role in host physiology such as obesity, diabetes, and various neurological diseases. Thus, microbiome sampling is a fundamental approach towards better understanding of possible diseases. However, conventional sampling methods, such as endoscopies or colonoscopies, are invasive and cannot reach the entire small intestine. To address this need, a battery-less 3D-printed sampling capsule, which can collect microbiome samples throughout the entirety of the GI tract was designed. The capsule (9 mm × 15 mm) consists of a 3D printed acrylic housing, a fast-absorbing hydrogel, and a flexible PDMS membrane. Fluids containing samples of the microbial flora within the GI tract enter the device through a sampling aperture on the cap of the device. Once the microbiome enters the housing, the hydrogel absorbs the fluid and swells, effectively protecting the samples within its polymeric matrix, while also pushing on the flexible PDMS membrane to block the sampling aperture from further fluid exchange. The retrieved capsule can be readily disassembled due to the screw-cap design of the capsule and the hydrogel can be removed for further bacterial culture and analysis. As a proof of concept, the capsule's bacterial sampling efficiency and the ability to host microbial samples within the hydrogel in a sealed capsule were validated using a liquid culture containing Escherichia coli. The demonstrated technology provides a promising inexpensive tool for direct sampling and assessment of microbes throughout the GI tract and can enable new insights into the role of diet in mediating host–microbe interactions and metabolism.
24 September 2022 in Acta Biomaterialia
1 June 2019 in Journal of Water Process Engineering
26 November 2021 in Lab on a Chip
Although serum and fecal biomarkers (e.g., lactoferrin, and calprotectin) have been used in management and distinction between inflammatory bowel disease (IBD) and irritable bowel syndrome (IBS), none are proven to be a differential diagnostic tool between Crohn's disease (CD) and ulcerative colitis (UC). The main challenge with laboratory-based biomarkers in the stool test is the inability to indicate the location of the disease/inflammation in the gastrointestinal (GI) tract due to the homogenous nature of the collected fecal sample. For the first time, we have designed and developed a battery-free smart capsule that will allow targeted sampling of inflammatory biomarkers inside the gut lumen of the small intestine. The capsule is designed to provide a simple and non-invasive complementary tool to fecal biomarker analysis to differentiate the type of IBD by pinpointing the site of inflammatory biomarkers secretion (e.g., small or large bowel) throughout the GI tract. The capsule takes advantage of the rapid change from an acidic environment in the stomach to higher pH levels in the small intestine to dissolve a pH-sensitive polymeric coating as a means to activate the sampling process of the capsule within the small intestine. A swelling polyacrylamide hydrogel is placed inside the capsule as a milieu to collect the sampled GI fluid while also providing the required mechanical actuation to close the capsule once the sampling is completed. The hydrogel component along with the collected GI fluid can be easily obtained from the capsule through the screw-cap design for further extraction and analysis. As a proof of concept, the capsule's performance in sampling and extraction of bovine serum albumin (BSA) and calprotectin – a key biomarker of inflammation – was assessed within the physiologically relevant ranges. The ratio of extracted biomarkers relative to that in the initial sampling environment remained constant (∼3%) and independent of the sampling matrix in both in vitro and ex vivo studies. It is believed that the demonstrated technology will provide immediate impact in more effective IBD type differential diagnostic and treatment strategies by providing a non-invasive assessment of inflammation biomarkers profile throughout the digestive tract.
1 October 2021 in Nano Energy
8 July 2022 in Journal of Materials Chemistry C
All-solid-state printed electrochemical sensors based on solid-contact ion-selective electrodes (SC-ISE) have shown great potential for use in many portable applications ranging from healthcare to environmental monitoring. Despite the low cost and scalable manufacturability of these sensors, they often underperform in long-term applications due to the formation of a water layer between the ion-selective membrane (ISM) and the printed electrode. Here, we report a simple approach to minimize the water layer formation and increase the stability of the SC-ISE by improving the interfacial bonding between the ISM and printed carbon electrodes through cold atmospheric plasma (CAP) treatment. A systematic study with different processing gas flow rates and power conditions was performed to identify the effect of CAP treatment on printed carbon electrode surface modification and to assess the role of functionalized surfaces in improving the sensor performance. To achieve maximal functionality, plasma settings were optimized with a minimum plasma power of 300 W and an oxygen flow rate of 120 mL min−1 which was further verified by surface characterization techniques including water contact angle measurements and Raman spectroscopy. X-Ray photoelectron spectra (XPS) of the plasma-treated (PT) electrode surfaces indicated the formation of functional groups including hydroxyl (–OH), carboxyl (–COOH), and carbonyl (–CO), all of which aided in maximizing surface energy and creation of strong covalent bonds between the printed carbon electrode and ISM. In addition, CAP treatment led to the decomposition/removal of impurities and the polymer binder from the surface of printed carbon which effectively increased the exposed uncontaminated graphene flakes on the surface of the electrodes. Finally, as a proof of concept, we demonstrated that the use of CAP treatment prior to the coating with a nitrate sensitive ISM resulted in improved chemical bonding between the layers and a significant reduction in the water layer formation, leading to enhanced long-term stability (7-fold improvement) as compared with that of the untreated electrode.