Mohammad Masoomi

Mohammad Masoomi

Auto-generated profile, based on publicly available information

Mohammad Masoomi

Laboratory for Fatigue & Additive Manufacturing Excellence (FAME), Department of Mechanical Engineering, Auburn University, Auburn, AL 36849, United States

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2017 in International Journal of Machine Tools and Manufacture
Verified
Journal Article
Closed access
MMMohammad Masoomi
Mohammad Masoomi
STScott M Thompson
Scott M Thompson
NSNima Shamsaei
Nima Shamsaei

1 August 2017 in Manufacturing Letters
Verified
Journal Article
Closed access
MMMohammad Masoomi
Mohammad Masoomi
STScott M Thompson
Scott M Thompson
NSNima Shamsaei
Nima Shamsaei

1 August 2017 in Data in Brief
Verified
Journal Article
Open access
MMMohammad Masoomi
Mohammad Masoomi
NSNima Shamsaei
Nima Shamsaei
RWRobert A. Winholtz
Robert A. Winholtz
JMJustin L. Milner
Justin L. Milner
TGThomas Gnäupel-Herold
Thomas Gnäupel-Herold
STScott M Thompson
Scott M Thompson
Neutron diffraction was employed to measure internal residual stresses at various locations along stainless steel (SS) 17-4 PH specimens additively manufactured via laser-powder bed fusion (L-PBF). Of these specimens, two were rods (diameter=8 mm, length=80 mm) built vertically upward and one a parallelepiped (8×80×9 mm3) built with its longest edge parallel to ground. One rod and the parallelepiped were left in their as-built condition, while the other rod was heat treated. Data presented provide insight into the microstructural characteristics of typical L-PBF SS 17-4 PH specimens and their dependence on build orientation and post-processing procedures such as heat treatment. Data have been deposited in the Data in Brief Dataverse repository (doi:10.7910/DVN/T41S3V).

1 August 2018 in Additive Manufacturing
Verified
Journal Article
Closed access
MMMohammad Masoomi
Mohammad Masoomi
JPJonathan W. Pegues
Jonathan W. Pegues
STScott M Thompson
Scott M Thompson
NSNima Shamsaei
Nima Shamsaei

13 November 2015
Verified
Conference Paper
Closed access
PDF file
MMMohammad Masoomi
Mohammad Masoomi
XGXiang Gao
Xiang Gao
STScott M Thompson
Scott M Thompson
NSNima Shamsaei
Nima Shamsaei
LBLinkan Bian
Linkan Bian
AEAlaa Elwany
Alaa Elwany
Selective Laser Melting (SLM), a laser powder-bed fusion (PBF-L) additive manufacturing method, utilizes a laser to selectively fuse adjacent metal powders. The powders are aligned in a bed that moves vertically to allow for layer-by-layer part construction-Process-related heat transfer and thermal gradients have a strong influence on the microstructural features, and subsequent mechanical properties, of the parts fabricated via SLM. In order to understand and control the heat transfer inherent to SLM, and to ensure high quality parts with targeted microstructures and mechanical properties, comprehensive knowledge of the related energy and mass transport during manufacturing is required. In this study, the transient temperature distribution within and around parts being fabricated via SLM is numerically simulated and the results are provided to aid in quantify the SLM heat transfer. In order to verify simulation output, and to estimate actual thermal gradients and heat transfer, experiments were separately conducted within a SLM machine using a substrate with embedded thermocouples. The experiments focused on characterizing heat fluxes during initial deposition on an initially-cold substrate and during the fabrication of a thin-walled structure built via stainless steel 17-4 powders. Results indicate that it is important to model heat transfer thorough powder bed as well as substrate.

1 December 2018 in Additive Manufacturing
Verified
Journal Article
Closed access
MMMuztahid Muhammad
Muztahid Muhammad
MMMohammad Masoomi
Mohammad Masoomi
BTBrian Torries
Brian Torries
NSNima Shamsaei
Nima Shamsaei
MHMeysam Haghshenas
Meysam Haghshenas