28 June 2024 in Journal of Materials Science & Technology
15 April 2026 in SSRN Electronic Journal
In Ni-based single-crystal superalloys, the pronounced microstructural sensitivity to subtle compositional variations within a vast multicomponent space renders experimental establishment of composition–microstructure mappings infeasible. In this work, using phase-field simulation data of the Ni–Al–Mo system, we develop a Composition-Conditioned Latent Diffusion Transformer (CCLDT) for the generalized generation of microstructure images within the continuous composition space. Built on the Latent Diffusion Model (LDM) framework, CCLDT employs a Diffusion Transformer (DiT) as its denoising backbone. Through the optimization of its compositional conditioning mechanism, CCLDT yields mean Intra-FID scores of 11.31 and 18.70 under seen and unseen compositions, respectively, demonstrating superior visual fidelity in the learned generative mapping. Furthermore, for each physical statistical descriptor, over 75% of the points show low deviations: specifically, absolute errors below 0.02 for γ′ volume fraction and relative errors below 6% for the autocorrelation function (ACF), thereby validating the model’s physical reliability within the continuous composition space. Importantly, CCLDT highlights Mo’s dominant role and its synergistic interaction with Al, aligning generative modeling with underlying physical mechanisms such as lattice misfit and energy balance. In addition, the alignment of Intra-FID with physical metrics demonstrates its effectiveness in microstructural assessment. To the best of our knowledge, this work presents the first application of a DiT-based latent diffusion model for Ni-based single-crystal superalloys, enabling generative mapping from continuous composition space to microstructures.
7 September 2026 in SSRN Electronic Journal
The effectiveness of microstructural recovery (RE) in single-crystal (SX) superalloys remains poorly understood when creep damage is compounded by thermal or thermomechanical excursions. Here, we systematically distinguish creep, thermal, and thermomechanical damage by combining creep interruption, thermal exposure (TE), over-temperature creep (OC), rejuvenation heat treatment (RHT), and subsequent re-creep. A nickel-based SX superalloy was creep interrupted at 1000 °C/280 MPa and subsequently subjected to TE at 1200 °C for 2 h or OC at 1200 °C/80 MPa for 30 min. RE after creep interruption produced a stable total creep life extension exceeding 35%. TE generated secondary γ' precipitates without markedly degrading creep resistance, and RE extended the total creep life by 45%. In contrast, OC promoted premature γ' cutting by dislocations and pronounced creep degradation, limiting the life extension after RE to 23%. Microstructural analysis reveals that γ' and dislocation degradation is largely reversible, whereas carbide- and pore-related damage limits creep life restoration. γ' dissolution during RHT further facilitates dislocation annihilation and rearrangement into lower-energy configurations. These findings clarify the damage-dependent recoverability and define the applicability limits of RHT for life extension of SX superalloys under complex thermal and thermomechanical histories.
16 October 2026 in SSRN Electronic Journal
Fatigue tests of SiCf/SiC composites fabricated by chemical vapor infiltration (CVI) combined with polymer infiltration and pyrolysis (PIP) were conducted at 1350 °C at 160, 200, and 240 MPa, wherein the mechanical damage and oxidative erosion were elucidated by acoustic emission (AE) equipment and SEM. The material exhibited distinct mechanical behaviors and AE signals across different stresses. During fatigue at 160 MPa, the cumulative AE energy increased rapidly and then remained constant, whereas at 200 MPa and 240 MPa, it increased continuously until fracture. The specimens did not fracture after 105 and 106 cycles at 160 MPa, with tensile strength retention rates of 88 ± 4% and 65 ± 3%, respectively. Room-temperature tensile tests were conducted on the unfractured specimens for comparison with the as-received ones. The study showed that the CVI-SiC matrix damaged at high stress, and cracks served as channels for oxygen. inducing interfacial degradation and material failure.
14 April 2026 in SSRN Electronic Journal
A novel Ni₃Al-based single-crystal superalloy was subjected to creep testing at 1200°C under applied stresses ranging from 60 to 100 MPa. The stress-related deformation mechanism was elucidated through creep performance testing and examination of microstructure evolution. The results reveal pronounced stress sensitivity, with creep life decreasing from 360.5 h to 22.6 h as the stress increased from 60 to 100 MPa. Meanwhile, the creep strain during the primary creep stage rises from 0.59% to 1.68%. In contrast, during the steady-state creep stage, a decrease in applied stress from 100 MPa to 60 MPa leads to a significant reduction in the minimum creep rate, which drops from 2.77×10⁻⁷ s⁻¹ to 5.02×10⁻⁹ s⁻¹. This behavior is closely associated with the evolution of the interfacial dislocation network at γ/γ′ interfaces, whose spacing plays a critical role in controlling the steady-state creep rate. Throughout the tertiary creep stage, the degree of topological inversion is markedly enhanced with increasing applied stress. At the same time, a concomitant decline is observed in the number density of γ′ subgrains adjacent to the fracture surface. Under an applied stress of 60 MPa, the predominant creep mechanism is confirmed to be dislocation climb. At 100 MPa, the mechanism transitions to dislocation shearing of the γ′ precipitates. In summary, this study reveals the microstructural evolution and dominant deformation mechanisms under varying stress conditions at 1200℃, providing foundational data for the material selection of turbine blades in advanced aeroengines.
17 September 2026 in SSRN Electronic Journal
Single-crystal superalloys require excellent ultrahigh-temperature creep resistance for advanced aero-engines, demanding suppression of dislocation motion and microstructural instability. Unlike complex and unpredictable compositional tuning, we propose an aging-strengthening strategy for interfacial dislocation regulation. High-density interfacial dislocations are introduced to fully exploit their roles in impeding dislocation motion and facilitating solute transport, maximizing interfacial strengthening through the interfacial dislocation network and the γ/γ′ interfacial morphology. This strategy stems from the unique role of lattice misfit during short-time ultrahigh-temperature aging. We clarified the kinetic sequence of misfit-stress relaxation and γ′ dissolution. Under specific treatment conditions, the increased γ/γ′ lattice misfit preferentially induces misfit-stress relaxation, thereby forming high-density misfit dislocations before extensive γ′ dissolution occurs. These dislocations rapidly form a stable, dense interfacial dislocation network with spacings approaching the theoretical value for the overheating-induced highly negative misfit. Moreover, pipe diffusion along these dislocations utilizes γ′ dissolution, which is typically considered fatal to ultrahigh-temperature stability, to maintain the γ/γ′ interfacial density. This strategy enables low-density alloys with high-γ′ fractions to attain exceptional creep resistance, with creep life at 1200 °C increasing by more than 80% at 80 MPa and exceeding 290 h at 60 MPa. More broadly, aging treatments can be extended from morphological control to dislocation regulation, with misfit as the core trigger. This not only enhances superalloy creep resistance but also provides new insights for tuning the mechanical properties of other multiphase metallic materials.