When activated with base, the iron(II) complexes with tetradentate amine(imine)diphosphine ligands, (S,S)-trans-[FeCl(CO)(PAr2-NH-N-PAr′2)]BF4 (1: Ar, Ar′ = Ph; 2: Ar = Ph, Ar′ = 4-MeC6H4; 3: Ar, Ar′ = 3,5-Me2C6H3), are very active for the asymmetric transfer hydrogenation (ATH) of ketones in KOtBu/2-propanol. For ATH, better enantioselectivity, but lower catalytic activity, was observed in general when using catalyst precursors with the bulkier dixylylphosphino groups compared to those with diphenylphosphino groups. The complexes were much less active for the pressure hydrogenation of ketones, where 1 and 2 produced racemic product alcohols, while 3 yielded chiral alcohols with an enantiomeric excess of up to 70% (R) at turnover frequencies up to 80 h–1 and turnover numbers of 100 for a range of ketones at 50 °C and 20 atm H2. This is a rare example of asymmetric pressure hydrogenation using an iron complex. Unlike the case of ATH, there is no effect on the rate upon the addition of KOtBu beyond the 2 equiv needed to convert the precursor complex to the active amido(ene-amido) and amine(ene-amido)hydrido forms. Both AH and ATH reactions share the same iron hydride intermediate formed by reaction of the amido(ene-amido) iron complex with either dihydrogen or 2-propanol. Kinetic studies on the H2 hydrogenation of acetophenone catalyzed by 1, activated by base in benzene, using the method of initial rates indicated that the heterolytic splitting of the dihydrogen at the amido(ene-amido) iron complex is the turnover-limiting step of the catalytic cycle for hydrogenation. For 1 in benzene at 323 K over the ranges of concentrations [1] = (2.4–4.8) × 10–4 M and [ketone] = (3.6–7.2) × 10–2 M, and of H2 pressures = 10–20 atm, the rate law is rate = k[1][H2], with k = 0.16 ± 0.01 M–1 s–1, ΔH⧧ = 10.0 ± 0.2 kcal mol–1, and ΔS⧧ = −31.0 ± 0.5 cal mol–1 K–1. Detailed DFT calculations also support the finding that the barrier for H2 splitting is the turnover-limiting step. The higher barrier for H2 activation compared to isopropanol activation in order to generate the active amine(ene-amido)hydrido form explains why this system is biased toward ATH over AH.
The excellent ketone asymmetric transfer hydrogenation (ATH) systems using the precatalysts (S,S)-trans-[FeCl(CO)(PPh2CH2CH2NHCHPhCHPhNCHCH2PAr2)]BPh4 (Ar = Ph (1), p-tolyl (2)) have a fascinating dependence of activity on the base concentration, which is investigated here. The reaction of complex 1 or 2 with 1 equiv of the strong base potassium tert-butoxide in THF for 2–7 days produces the neutral amine(ene-amido) complexes [FeCl(CO)(PPh2CH2CH2NHCHPhCHPhNCHCHPAr2)] (8 and 9). These monodeprotonated complexes have been completely characterized by NMR, EA, and FT-IR spectroscopy and mass spectrometry, and the structure of 9 has been further confirmed by single-crystal X-ray diffraction to reveal a structure with the NH and FeCl bonds parallel and the proton and chloride ligands next to each other. The structures of 8 and 9 and their 1H NMR patterns are similar to those of the active catalyst for the ATH of ketones that is postulated to have NH and FeH bonds parallel with the protonic and hydridic hydrogens adjacent. Identical key nuclear Overhauser effect (NOE) correlations in both 8 and the hydrido complex provide further evidence for the postulated structure of the amine iron hydride intermediate. The catalyst system is not active for the transfer hydrogenation of acetophenone, unless greater than 2 equiv of base is added to activate the precatalyst. The addition of base (up to 8 equiv per iron) increases the reaction rate, while a further increase of the base concentration shows a reduction of activity. The loss of activity with less than 2 equiv of base results from a side reaction of the active amido(ene-amido) complexes with 2-propanol to form an inactive neutral bis(amido) iron complex, which was characterized by NMR spectroscopy. Structural evidence for this was provided by the X-ray crystal structure determination of an analogous bis(amino) iron(II) complex, generated from the reaction of the amine(ene-amido) iron complex with methanol in C6D6 in the presence of BF4–. The presence of excess base prevents this side reaction, thereby favoring the reaction which forms the active amine iron hydride species that is in the catalytic cycle. The structure of the transition state for the reaction of the amine hydrido iron catalyst with acetophenone has been successfully modeled using density functional theory (DFT) calculations. The (R) configuration of the product 1-phenylethanol is induced by the position of the phenyl groups on the catalyst and a π–π stabilizing interaction between the aryl ring on the ketone and the ene-amido moiety on the ligand.