In order to improve the mechanical and electromagnetic robustness of REBCO coated conductors (CCs) for their application in superconducting equipment, we have developed and characterized Face-to-Face Double Stack (FFDS) CCs by stacking the superconducting surfaces of two single superconducting CCs together. In this work, we were able to produce FFDS CCs with a single length of over 400 m. I c characteristics were measured at different temperatures and magnetic fields, and 128.8 A/4 mm-w (70 K, 3 T) was achieved for FFDS with artificially pinned CCs. Furthermore, mechanical strength with critical bending diameter of 5 mm such as flatwise strength and twisting are also reported.
6 January 2025 in IEEE Transactions on Applied Superconductivity
Reducing AC loss in superconducting AC equipment is crucial because of its substantial contribution to the cryogenic load. Decreasing the filament width can mitigate hysteresis loss of REBa2Cu3O7−δ (REBCO, RE = rare earth elements) superconducting tapes, and segmenting the superconducting layer into multiple filaments is a viable reduction approach. However, filaments tend to connect when the inter-filament resistance is low. Therefore, we propose Cut and Aggregated Multifilamentary (CaAM) tapes with high inter-filament resistance achieved via the electrodeposition of polyimide across the entire tape. This tape configuration involves aligning four 1-mm-wide filaments in parallel and bonding them onto a polyimide substrate. AC loss measurements of short tapes exhibit a reduction at high magnetic fields. Additionally, we fabricated double pancake coils, each coil contained 80$\ \times $ 2 turns, wound with monofilament tape and CaAM tape (coils A and B, respectively) and assessed the AC loss of the fabricated coils in liquid nitrogen. Experimental results indicate that the AC loss of coil B, using CaAM tape, is greater than that of coil A in the low-current region. However, they are almost identical in the high-current region. In contrast to the multifilament tapes with low inter-filament resistance, CaAM tapes indicate the possibility of loss reduction when used in coils.
26 December 2024 in IEEE Transactions on Applied Superconductivity
During the fabrication of commercial REBa2Cu3O7-x (REBCO; RE: rare-earth element)-coated conductors (CCs), inhomogeneities with low critical current (Ic) are occasionally introduced, which may result in electromagnetic instability, particularly at low temperatures. To mitigate the degradation of the current carrying capabiity caused by these defects, we developed long face-to-face double-stacked (FFDS) CCs via reel-to-reel solder bonding process. Previously, we successfully fabricated 400-m-long FFDS CCs via this process and investigated their mechanical properties. However, the current transport properties are still unclear. In this study, we investigated the interfacial resistivity of the FFDS CCs made by the continuous soldering process, and it was confirmed that the joint resistivity is consistently between 40 to 50 nΩcm2 where the joint distances were changed to 3.5, 5.0, and 11.6 cm. In addition, the effect on the current carrying capability was also examined by using model samples in which we introduced artificial defects with almost 50% drop of local Ic. It has been demonstrated demonstrated that the transport current can be recovered at almost 85 to 90% of a defect-free CCs, with Ic nearly two times of the strand, thanks to the current sharing effect through the solder joints. Namely, the interface resistivity of 40–50 nΩcm2 by our process was sufficiently small to obtain a current sharing effect and suppress the influence of the local inhomogeneity effectively.
13 February 2026 in IEEE Transactions on Applied Superconductivity
Reducing AC losses in superconducting AC devices is crucial as it significantly contributes to decreasing the cryogenic load. One effective approach to mitigate the hysteresis loss of REBa₂Cu₃O₇−δ (REBCO) superconducting tapes is to subdivide the superconducting layer into multiple filaments and minimize the filament width. Our research group has successfully reduced the AC loss in short-length segmented tapes using laser scribing. In previous studies, striated conductors with only a silver stabilization layer were used, but there were concerns about current bypassing during quenching. In this study, we developed striated copper-coated REBCO tape using laser scribing. To suppress localized heating during quenching, copper-coated tapes were striated using laser ablation. However, exposure of the edge during laser ablation poses the risk of moisture corrosion. To avoid this, the entire tape was coated with electrodeposited polyimide to protect the exposed areas. Subsequently, the AC losses of the striated and non-striated tapes were evaluated. First, the AC losses of short samples were assessed using the saddle-shaped pickup coil method. Subsequently, a double-pancake coil was fabricated using these tapes, and its AC losses were evaluated in liquid nitrogen. These coils had an inner diameter of 40 mm, outer diameter of 59.04 mm, and consisted of a double-pancake structure with 80 turns per pancake.
20 January 2026 in IEEE Transactions on Applied Superconductivity
REBa2Cu3O7-δ (REBCO, RE: rare earth element) coated conductors (CCs) have superior in-field performance compared to low-temperature superconductors and Bi-based superconductors, however, due to its crystal structure, REBCO CCs exhibit significant anisotropy, i.e., critical current density (Jc) is generally high for B // a-b and low for B // c-axis. Isotropic angular dependence would be ideal for such applications as magnets and coils, because anisotropic angular dependence will hinder current carrying capability in the winding and also make it more difficult for quench protection. To realize an isotropic angular dependence, artificial pinning centers (APCs), such as BaMO3 (M: Metal), have been introduced to enhance Jc for B // c-axis. However, it is still challenging to enhance pinning over all angles. In this study, we investigated a possible way to improve the angular dependence of REBCO CCs by applying face-to-face double-stacked (FFDS) configuration. Our previous study showed that FFDS interface resistivity is around 50 nΩcm2 at 77 K, enabling sufficient current sharing with small enough dissipation in cases of local Jc degradation in one side of the REBCO CC. In addition, Based on this finding, we examined whether to compensate for the angular dependence of the REBCO CCs. We made a FFDS CC by combining two REBCO CCs with different angular dependences, i.e., YBa2Cu3O7-δ (YBCO) CC with low Jc for B // c-axis and EuBa2Cu3O7-δ (EuBCO) with BaHfO3 (BHO) doping CC which has high Jc for B // c-axis. Current–voltage (I-V) measurements at various angles confirmed that FFDS CCs facilitate current sharing under applied fields. As a result, we analyze the I-V characteristics by applying an equivalent circuit model and confirmed the more isotropic angle dependence of Ic properties as designed. In conclusion, the FFDS configuration provides a practical means to current-carrying performance compared to the original CC strands and presents a practical method for tailoring REBCO CCs angular dependence with flexibility.