Though shallow flow of hydrothermal fluids in Long Valley Caldera, California, has been well studied, neither the hydrothermal source reservoir nor heat source has been well characterized. Here a grid of magnetotelluric data were collected around the Long Valley volcanic system and modeled in 3‐D. The preferred electrical resistivity model suggests that the source reservoir is a narrow east‐west elongated body 4 km below the west moat. The heat source could be a zone of 2–5% partial melt 8 km below Deer Mountain. Additionally, a collection of hypersaline fluids, not connected to the shallow hydrothermal system, is found 3 km below the medial graben, which could originate from a zone of 5–10% partial melt 8 km below the south moat. Below Mammoth Mountain is a 3 km thick isolated body containing fluids and gases originating from an 8 km deep zone of 5–10% basaltic partial melt.
30 October 2014 in Journal of Geophysical Research: Solid Earth
We use seismic, tilt, lidar, thermal, and gravity data from 32 consecutive eruption cycles of Lone Star geyser in Yellowstone National Park to identify key subsurface processes throughout the geyser's eruption cycle. Previously, we described measurements and analyses associated with the geyser's erupting jet dynamics. Here we show that seismicity is dominated by hydrothermal tremor (~5–40 Hz) attributed to the nucleation and/or collapse of vapor bubbles. Water discharge during eruption preplay triggers high‐amplitude tremor pulses from a back azimuth aligned with the geyser cone, but during the rest of the eruption cycle it is shifted to the east‐northeast. Moreover, ~4 min period ground surface displacements recur every 26 ± 8 min and are uncorrelated with the eruption cycle. Based on these observations, we conclude that (1) the dynamical behavior of the geyser is controlled by the thermo‐mechanical coupling between the geyser conduit and a laterally offset reservoir periodically filled with a highly compressible two‐phase mixture, (2) liquid and steam slugs periodically ascend into the shallow crust near the geyser system inducing detectable deformation, (3) eruptions occur when the pressure decrease associated with overflow from geyser conduit during preplay triggers an unstable feedback between vapor generation (cavitation) and mass discharge, and (4) flow choking at a constriction in the conduit arrests the runaway process and increases the saturated vapor pressure in the reservoir by a factor of ~10 during eruptions.
A three‐dimensional (3‐D) electrical resistivity model of Mono Basin in eastern California, unveils a complex subsurface filled with zones of partial melt, fluid‐filled fracture networks, cold plutons, and regional faults. In 2013, 62 broadband magnetotelluric stations were collected in an array around southeastern Mono Basin from which a 3‐D electrical resistivity model was created with a resolvable depth of 35 km. Multiple robust electrical resistivity features were found that correlate with existing geophysical observations. The most robust features are two 300 ± 50 km3 near‐vertical conductive bodies (3–10 Ω m) that underlie the southeast and northeastern margin of Mono Craters below 10 km depth. These features are interpreted as magmatic crystal‐melt mush zones of 15 ± 5% interstitial melt surrounded by hydrothermal fluids and are likely sources for Holocene eruptions. Two conductive east dipping structures appear to connect each magma source region to the surface. A conductive arc‐like structure (< 0.9 Ω m) links the northernmost mush column at 10 km depth to just below vents near Panum Crater, where the high conductivity suggests the presence of hydrothermal fluids. The connection from the southernmost mush column at 10 km depth to below South Coulée is less obvious with higher resistivity (200 Ω m) suggestive of a cooled connection. A third, less constrained conductive feature (4–10 Ω m) 15 km deep, extending to 35 km is located west of Mono Craters near the eastern front of the Sierra Nevada escarpment and is coincident with a zone of sporadic, long‐period earthquakes that are characteristic of a fluid‐filled (magmatic or metamorphic) fracture network. A resistive feature (103–105 Ω m) located under Aeolian Buttes contains a deep root down to 25 km. The eastern edge of this resistor appears to structurally control the arcuate shape of Mono Craters. These observations have been combined to form a new conceptual model of the magmatic system beneath Mono Craters to a depth of 30 km.