25 August 2017 in IEEE Transactions on Industrial Electronics
Wireless power transfer (WPT) has drawn more and more attention and has many applications, such as wireless electric vehicle charging systems, which require high power, high efficiency, and high power factor. In this paper, a single-stage WPT resonant converter with bridgeless boost power-factor-correction (PFC) rectifier is proposed to improve efficiency and power quality of line input, and reduce production cost and complexity for high-power WPT system. The bridgeless single-stage topology is creatively proposed to apply in WPT system, which is much more advantageous than conventional two-stage WPT converter with individual boost PFC stage.
29 December 2020 in IEEE Transactions on Transportation Electrification
Mutual inductance and load condition of a wireless power transfer system are essential parameters to regulate the output voltage and power or track maximum efficiency. This paper proposes a parameter identification approach for the DC-DC WPT resonant converter only requiring the primary-side measurement to identify the mutual inductance, output voltage, output power, and efficiency under unknown varying misalignment and load conditions. The approach is widely applicable to series-series, series-parallel, parallel-series, parallel-parallel, and LCC-C topologies and can estimate the value variation of the resonant capacitors, which are the unique advantages as compared to other existing methods. Moreover, there is no restriction on the operation frequency selection. Direct-quadrature transformation technique is applied to acquire the fundamental and third-order harmonics information of primary-side voltage and current accurately. Detailed analysis, hardware design, and laboratory prototype are presented with experimental results to validate the correctness and accuracy of the proposed approach.
25 May 2022 in IEEE Transactions on Industrial Electronics
Single-phase ac–dc wireless power transfer (WPT) converters are widely used in grid-connected systems, such as wireless electric vehicle chargers. Traditional two-stage topology with an ac–dc power factor correction (PFC) rectifier stage and a dc–dc WPT converter stage cannot achieve the highest overall efficiency and the lowest production cost. Moreover, two separate controllers are required. Recently, a single-phase single-stage ac–dc WPT converter with a front-end boost bridgeless PFC rectifier was proposed to overcome the drawbacks of two-stage topologies. However, two front-end diodes are still required for rectification, and the input power quality is not sufficiently high as the input current is not actively shaped. In this article, a compact single-phase integrated-power-stage ac–dc WPT converter with only four active power switches and four diodes is proposed. The full-bridge switches are utilized to perform ac–dc PFC rectification and dc–dc WPT conversion simultaneously. Description of the proposed topology with the modulation and control methods, operation principle, power loss analysis, and referenced design procedure are presented in detail. Finally, a 500-W laboratory prototype is implemented, and the corresponding experimental results are given to validate the principle, analysis, and design.
13 May 2019 in IEEE Journal of Emerging and Selected Topics in Power Electronics
9 March 2022 in IEEE Transactions on Industrial Electronics
Significant improvement in the power efficiency of dual-active-bridge dc–dc converters can be achieved by implementing zero voltage switching (ZVS) which is facilitated by a negative switch current at the switching instant. Such negative current, however, causes undesirable backflow power that counteracts the efficiency gain. Thus, the conditions for achieving ZVS and maintaining minimum backflow power (MBP) are often conflicting. A design that implements ZVS and MBP simultaneously is, thus, desirable. While, existing research is short of exploring the accurate condition of MBP and ZVS. This work fully considers the influence of output capacitance of power switches on ZVS and tries to implement ZVS and MBP of a dual-active-bridge dc–dc converter by controlling the inductor current to a minimum value at the turn- off instant of a power switch. The expression of the minimum switching current for ZVS and MBP is first derived by considering the resonant transient process in dead time. The transmission power range with ZVS and MBP can be maximized by selecting appropriate voltage conversion ratio according to different values of minimum current. An optimal extended phase-shift control for enlarging the operating region for ZVS and MBP of a dual-active-bridge dc–dc converter is designed. The optimization method is experimentally verified.
7 March 2022 in IEEE Transactions on Power Electronics
Bidirectional ac–dc wireless power transfer (WPT) converters are widely used in grid-connected electric vehicle systems for grid-to-vehicle and vehicle-to-grid applications. They usually apply a two-stage topology with a bidirectional ac–dc power factor correction converter and a bidirectional dc–dc WPT converter. Such a two-stage topology cannot achieve high efficiency and low cost. Recently, single-stage matrix bidirectional ac–dc WPT converters have been proposed. However, the matrix-converter-based topologies do not utilize remarkably lower count of power switches and generate large double-line frequency ripple in the dc-side voltage or current. This article proposes a new single-phase bidirectional ac–dc WPT topology with an integrated power stage to overcome the drawbacks of the matrix-converter-based topologies and retain the advantages of single-stage topologies. Description of the proposed topology with the modulation and control methods, theoretical analysis, and reference design procedure are presented in detail. Finally, a scaled-down laboratory prototype with 500-W output power is implemented with experimental results presented to validate the principle, analysis, and design.