11 February 2017 in Journal of Advances in Modeling Earth Systems
A new windblown dust emission treatment was incorporated in the Community Multiscale Air Quality (CMAQ) modeling system. This new model treatment has been built upon previously developed physics‐based parameterization schemes from the literature. A distinct and novel feature of this scheme, however, is the incorporation of a newly developed dynamic relation for the surface roughness length relevant to small‐scale dust generation processes. Through this implementation, the effect of nonerodible elements on the local flow acceleration, drag partitioning, and surface coverage protection is modeled in a physically based and consistent manner. Careful attention is paid in integrating the new windblown dust treatment in the CMAQ model to ensure that the required input parameters are correctly configured. To test the performance of the new dust module in CMAQ, the entire year 2011 is simulated for the continental United States, with particular emphasis on the southwestern United States (SWUS) where windblown dust concentrations are relatively large. Overall, the model shows good performance with the daily mean bias of soil concentrations fluctuating in the range of ±1 µg m−3 for the entire year. Springtime soil concentrations are in quite good agreement (normalized mean bias of 8.3%) with observations, while moderate to high underestimation of soil concentration is seen in the summertime. The latter is attributed to the issue of representing the convective dust storms in summertime. Evaluations against observations for seven elevated dust events in the SWUS indicate that the new windblown dust treatment is capable of capturing spatial and temporal characteristics of dust outbreaks.
22 December 2016 in Journal of Geophysical Research: Atmospheres
A coupled photosynthesis‐stomatal conductance model with single‐layer sunlit and shaded leaf canopy scaling is implemented and evaluated in a diagnostic box model with the Pleim‐Xiu land surface model (PX LSM) and ozone deposition model components taken directly from the meteorology and air quality modeling system—WRF/CMAQ (Weather Research and Forecast model and Community Multiscale Air Quality model). The photosynthesis‐based model for PX LSM (PX PSN) is evaluated at a FLUXNET site for implementation against different parameterizations and the current PX LSM approach with a simple Jarvis function (PX Jarvis). Latent heat flux (LH) from PX PSN is further evaluated at five FLUXNET sites with different vegetation types and landscape characteristics. Simulated ozone deposition and flux from PX PSN are evaluated at one of the sites with ozone flux measurements. Overall, the PX PSN simulates LH as well as the PX Jarvis approach. The PX PSN, however, shows distinct advantages over the PX Jarvis approach for grassland that likely result from its treatment of C3 and C4 plants for CO2 assimilation. Simulations using Moderate Resolution Imaging Spectroradiometer (MODIS) leaf area index (LAI) rather than LAI measured at each site assess how the model would perform with grid averaged data used in WRF/CMAQ. MODIS LAI estimates degrade model performance at all sites but one site having exceptionally old and tall trees. Ozone deposition velocity and ozone flux along with LH are simulated especially well by the PX PSN compared to significant overestimation by the PX Jarvis for a grassland site.
16 February 2022 in ESS Open Archive
Dry deposition of aerosols from the atmosphere is an important but poorly understood and inadequately modeled process in atmospheric systems for climate and air quality. Comparisons of currently used aerosol dry deposition models to a compendia of published field measurement studies in various landscapes show very poor agreement over a wide range of particle sizes. In this study, we develop and test a new aerosol dry deposition model that is a modification of the current model in the Community Multiscale Air Quality (CMAQ) model that agrees much better with measured dry deposition velocities across particle sizes. The key innovation is the addition of a second inertial impaction term for microscale obstacles such as leaf hairs, microscale ridges, and needleleaf edge effects. The most significant effect of the new model is to increase the mass dry deposition of the accumulation mode aerosols in CMAQ. Accumulation mode mass dry deposition velocities increase by almost an order of magnitude in forested areas with lesser increases for shorter vegetation. Peak PM 2.5 concentrations are reduced in some forested areas by up to 40% in CMAQ simulations. Over the continuous United States, the new model reduced PM 2.5 by an average of 16% for July 2018 at the Air Quality System monitoring sites. For summer 2018 simulations, bias and error of PM 2.5 concentrations are significantly reduced, especially in forested areas.
25 July 2022 in ESS Open Archive
Dry deposition of aerosols from the atmosphere is an important but poorly understood and inadequately modeled process in atmospheric systems for climate and air quality. Comparisons of currently used aerosol dry deposition models to a compendia of published field measurement studies in various landscapes show very poor agreement over a wide range of particle sizes. In this study, we develop and test a new aerosol dry deposition model that is a modification of the current model in the Community Multiscale Air Quality (CMAQ) model. The new model agrees much better with measured dry deposition velocities across particle sizes. The key innovation is the addition of a second inertial impaction term for microscale obstacles such as leaf hairs, microscale ridges, and needleleaf edge effects. The most significant effect of the new model is to increase the mass dry deposition of the accumulation mode aerosols in CMAQ. Accumulation mode mass dry deposition velocities increase by almost an order of magnitude in forested areas with lesser increases for shorter vegetation. Peak PM2.5 concentrations are reduced in some forested areas by up to 40% in CMAQ simulations. Over the continuous United States, the new model reduced PM2.5 by an average of 16% for July 2018 at the Air Quality System monitoring sites. For summer 2018 simulations, bias and error of PM2.5 concentrations are significantly reduced, especially in forested areas.