28 December 2022 in Bulletin of the National Technical University «KhPI» Series: Engineering and CAD
At the stage of design research of armored bodies of lightly armored vehicles it is extremely important to determine the range of their natural frequencies and natural forms of oscillation. For this purpose, the finite element method is usually used. It is necessary to substantiate the parameters of the finite element model, which provide an acceptable level of accuracy of numerical modeling of dynamic properties of this type of structures. For this purpose, data from parallel numerical and experimental studies of the mock-up of the armored hull of the armored personnel carrier are used. The mock-up of the upper projection of the armored hull is made in the appropriate scale. The material is sheet steel. This mock-up is subjected to dynamic excitation on a vibrating table. Resonant excitation frequencies are recorded, as well as the natural vibration forms. Shock-pulse excitation of the armored hull’s mock-up was also performed. The response to this excitation is recorded using accelerometers. Then, the spectrum of natural vibration frequencies is determined from these oscillograms. In parallel, numerical modeling of natural frequencies and natural vibration forms of the armored hull’s mock-up is carried out. After that, the results of numerical and experimental studies are compared. By varying the parameters of the finite element model, a satisfactory correspondence between the results of numerical calculations and experimental measurements is achieved. In particular, the following are determined: the acceptable type of used finite elements; the number of finite elements required to satisfy the accuracy of numerical modeling of the dynamic properties of similar structures; zones of the recommended thickening-rarefaction of a grid of finite elements, etc. According to the research results, the parameters of finite-element models have been established, which can be used to study the dynamic processes and properties of full-scale armored hulls of lightly armored vehicles. Keywords: lightly armored vehicle, mock-up, natural frequency, spectrum of natural vibration frequencies
22 May 2023 in Bulletin of the National Technical University «KhPI» Series: Engineering and CAD
The work describes computational and experimental studies of the stress-strain state of elements of technological systems. The distribution of movements of individual surfaces is determined on the example of vice-type adjustable machine tools. In the course of experimental studies, normal displacements are determined from the pattern of stripes on the hologram. The components of the displacement vector in the plane of the investigated surfaces are determined by scanning speckle interferograms. The obtained distributions of the displacement components were compared with the distributions determined by the finite element method. Satisfactory convergence of the results of numerical and experimental studies has been confirmed. The constructed calculation models can be used for further studies of the behavior of the housings of vice-type devices under the action of complex loads. The advantage of the developed version of the calculation-experimental method of studying the stress-strain state is its direct focus on the verification of the calculation model. The basic results are the results of experimental studies in the form of patterns of interference bands. These pictures describe the distribution of displacement fields of points on the surfaces of the bodies under study. With this picture, which was obtained on a natural object, the pictures of displacement fields, which were obtained during calculations with the application of the finite element method, are compared. Numerically calculated pictures are modified depending on the boundary conditions that are applied, as well as on the characteristics of the finite element models that are being built. In order to determine adequate boundary conditions and acceptable variants of finite-element models, the functional of the discrepancy of the displacement distribution fields obtained, on the one hand, numerically, and on the other - experimentally, is minimized. This construction of the calculation model verification algorithm demonstrated its efficiency and effectiveness. Keywords: stress-strain state; technological system; machine tool; finite element method; contact interaction
18 December 2023 in Bulletin of the National Technical University «KhPI» Series: Engineering and CAD
При оснащенні танкових двигунів високообертовими елементами виникає низка проблем. Вони повязані з необхідністю аналізу напружено-деформованого стану та критичних режимів обертання цих елементів. Відповідно, потребує поглибленого аналізу вимоги та конструктивні рішення двигунів та їхніх високообертових елементів. Крім того, привертають увагу сучасні дослідження динаміки двигунів. Також слід звернути увагу на аналіз існуючих конструкцій систем турбонаддуву танкових двигунів. При цьому важливим є аналіз моделей та методів дослідження статичного та динамічного напружено-деформованого стану робочих коліс турбокомпресорів. Здійснений аналіз проблемних аспектів два можливість відзначити, що натепер проблема дослідження напружено-деформованого стану та критичних режимів обертання високообертових елементів танкових та двигунів для бронетехніки не має завершеного вирішення. Потрібні нові підходи, моделі та методи і засоби дослідження, що створюють основу для обґрунтування прогресивних технічних рішень. Ключові слова: бронетехніка; танкові двигуни; турбокомпресор; високообертові елементи; напружено-деформований стан
29 May 2026 in Bulletin of the National Technical University «KhPI» Series: Engineering and CAD
In many machine-building structures, parts that are in contact interaction are widespread. In many cases, such interaction occurs on surfaces that nominally coincide or are close. That is, the gap between the bodies is nominally either zero or very small. In these cases, two factors become important factors. The first is the contact stiffness, which is determined by the properties of the near-surface layers of materials. The second factor is the perturbation of the geometric shape of the contacting surfaces. Examples can be elements of bearings, engines, rotor supports, dies, molds, etc. To study the contact interaction and the stress-strain state of such contacting bodies, a variational formulation has been developed. This formulation consists of adapting the Kalker variational principle. An additional term is added to the additional work functional, which depends on the properties of the near-surface layers of the contacting bodies and on the shape of the contacting surfaces. Thus, a single mathematical model takes into account both important factors. The boundary element method is used to discretize the problem. For this purpose, the desired contact pressure is approximated by a set of piecewise linear functions based on a triangular network. As a result, the problem of minimizing a quadratic function on a set of linear constraints in the form of inequalities arises. As an example, an analysis of the contact interaction of a ball piston with a running track of a radial hydraulic transmission is carried out
28 December 2024 in Bulletin of the National Technical University «KhPI» Series: Engineering and CAD
The work is aimed at ensuring high tactical and technical characteristics of domestic armored combat vehicles by increasing the contact strength of the most critical and loaded elements of the charging mechanisms. This is due to the fact that due to the conditions of combat operations in modern conditions, the load on these elements of armored combat vehicles is sharply increasing. In such conditions, traditional methods for calculating the contact strength of these elements by conditional stresses with correction factors are not applicable. Therefore, in the course of research, we improved the models of contact interaction based on the development of the theory of variational inequalities. This model includes both variable and sought-after modifications of the shape of the working surfaces of the contacting elements of armored combat vehicles and the properties of the materials of the surface layers. A search for progressive design and technological solutions for these elements has been carried out. This makes it possible to develop a new generation of charging mechanisms that allow for an increase in the caliber of weapon projectiles and the rate of fire from advanced standard weapons. Such advanced solutions make it possible to ensure the tactical and technical characteristics of domestic advanced armored combat vehicles at the world level. The regularities of the influence of the varied parameters (geometric shape and properties of surface layers) on the contact strength of the elements of the charging mechanisms of armored combat vehicles are established. In particular, a significant asymmetry of the area of contact interaction between rollers and drive sprockets was found. This effect is caused by the general deformation, first of all, of the rollers. In this case, the contact area is shifted to the periphery of the working surface. Accordingly, the modification of this working surface (the formation of a “barrel”) has a positive effect on the load capacity of the contacting elements. The levels of contact pressure and equivalent Mises stresses decrease.
24 April 2026 in Bulletin of the National Technical University «KhPI» Series: Engineering and CAD
The paper employs a parametric approach to investigate the stress-strain state and critical motion regimes of rotor systems in tank engine superchargers. Using a test assembly as an example, the influence of the bearing span on the critical speeds of the rotor was determined. The impact of overall dimensions on the stress-strain state of the compressor impeller was also analyzed. It was established that the loss of rotor stability within the investigated frequency range occurs at the first, second, and third modes. Accordingly, several strategies for detuning from hazardous operating regimes are proposed by shifting critical speeds beyond the operating range. Specifically, this can be achieved by either decreasing or increasing the critical frequencies, or through a combination of these methods. The stress-strain state of the compressor impeller is highly sensitive to changes in its geometric dimensions. Increasing the diameter significantly increases the displacement of the disk and blade points, which may lead to a loss of clearance between the rotor and stator, causing potential failure. Stresses in the impeller are localized in the blade-to-disk transition zone and within the disk itself. Consequently, the impeller diameter is primarily limited by strength and stiffness requirements, while the bearing span and impeller length are restricted by the criteria for detuning from critical speeds. The paper presents the distributions of the components of the stress-strain state of the compressor impeller at different values of the variable parameters, as well as at different rotor rotation frequencies. The forms of loss of stability of the compressor rotor part are also presented