Augusto Redolfi

Augusto Redolfi

Auto-generated profile, based on publicly available information

Augusto Redolfi

IMEC, Leuven, Belgium

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 May 2014 in IEEE Electron Device Letters
Verified
Journal Article
Closed access
JSJohan Swerts
Johan Swerts
MPMihaela Popovici
Mihaela Popovici
BKBen Kaczer
Ben Kaczer
MAMarc Aoulaiche
Marc Aoulaiche
ARAugusto Redolfi
Augusto Redolfi
MJMalgorzata Jurczak
Malgorzata Jurczak
Leakage currents as low as 10 -7 A/cm 2 at both 1 V and -1 V top electrode bias in the sub-0.4-nm equivalent SiO 2 thickness range are demonstrated in Ru/SrTiO x /Ru metal- insulator-metal capacitors in which the 8.5-nm SrTiO x layer is deposited by atomic layer deposition. The top electrode material and deposition technique as well as the postdeposition anneal are crucial parameters to control the leakage, not only at negative, but also at positive top electrode bias.

2 February 2018 in Nano Research
Verified
Journal Article
Closed access
PDF file
ABAttilio Belmonte
Attilio Belmonte
UCUmberto Celano
Umberto Celano
ZCZhe Chen
Zhe Chen
JRJanaki Radhaskrishnan
Janaki Radhaskrishnan
ARAugusto Redolfi
Augusto Redolfi
LGLudovic Goux
Ludovic Goux
Nonvolatile memory devices based on filamentary resistance switching (RS) areamong the frontrunners to fuel future devices and sensors of the internet of things (IoT) era. The capability of many metal-insulator-metal cells to switch between two distinctive resistive states in response to an external electrical stimulus has been demonstrated. Through years of selection, cells based on the drift of metal ions, namely conductive-bridge memory devices, have shown a wide range of applications with nanosecond switching speeds, nanometer scalability,high-density, and low power-consumption. However, for low (sub-10-μA) current operation, a critical challenge is still represented by programming variability and by the stability of the conductive filament over time. Here, by introducing the concept of reverse filament growth (RFG), we managed to control the structural reconfiguration of the conductive filament inside a memory cell with significant enhancements of each of the aforementioned properties. A first-in-class Cu-based switching device is demonstrated, with a dedicated stack that enabled us to systematically trigger RFG, thus tuning the device’s properties. Along with nanosecond switching speeds, we achieved an endurance of up to 106 cycles with a 102 read window, with outstanding disturb immunity and optimal stability of the filament over time. Furthermore, by tuning the filament’s shape, an excellent control of multi-level bit operations was achieved. Thus, this device offers high flexibility in memory applications.

1 June 2010
Verified
Conference Paper
Closed access
AMA. Mercha
A. Mercha
ARA. Redolfi
A. Redolfi
MSM. Stucchi
M. Stucchi
NMN. Minas
N. Minas
JOJ. Van Olmen
J. Van Olmen
BSBart Swinnen
Bart Swinnen
3D integration has the potential to alleviate the performance limitations that CMOS scaling is facing provided that it preserves the integrity of both front end and back end devices and constituting materials. The impact of wafer thinning and of the proximity of through silicon via on active devices, back end structures, ring oscillators and mixed signal circuit are reported for the first time for a High-k/Metal Gate first strained CMOS technology with low-k BEOL. The relative stress induced by the STI and the TSV are measured by micro-Raman spectroscopy. The measured impact of the stress on a sensitive DAC circuit is used to define a safe keep out area.

1 March 2011
Verified
Conference Paper
Closed access
ARA. Redolfi
A. Redolfi
ESE. Sleeckx
E. Sleeckx
KDK. Devriendt
K. Devriendt
DSD. Shamiryan
D. Shamiryan
TVT. Vandeweyer
T. Vandeweyer
DDD. L. Diehl
D. L. Diehl
This work presents a process to fabricate FinFETs in bulk silicon with advancements in critical fabrication steps such as STI trench oxide recess and adjustment of fin height. These steps are accomplished with the adoption of Siconi™ Selective Material Removal (SMR™) in the fabrication flow. FinFETs obtained with this new integration scheme were tested in a co-fabrication process flow proposed to integrate planar CMOS and FinFETs in the same wafer. Morphological and electrical results indicate perfectly filled trenches, better fin height control and bulk FinFET static performance similar to planar CMOS.

15 November 2019 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
JRJanaki Radhakrishnan
Janaki Radhakrishnan
ABAttilio Belmonte
Attilio Belmonte
WDWouter Devulder
Wouter Devulder
ARAugusto Redolfi
Augusto Redolfi
MHMichel Houssa
Michel Houssa
LGLudovic Goux
Ludovic Goux

1 June 2021
Verified
Conference Paper
Closed access
AGAlexandre La Grappe
Alexandre La Grappe
EVEvert Visker
Evert Visker
ARAugusto Redolfi
Augusto Redolfi
LPLan Peng
Lan Peng
KMKarthik Muga
Karthik Muga
JAJan Ackaert
Jan Ackaert
Patterning on Si with high aspect ratio trenches by spin-coating of photoresist faces significant challenges. The desire to maintain a good thickness uniformity of resist on wafer surface, to minimize any residue inside deep trenches, as well as enabling low cost of ownership has led to new process techniques. Wafer level lamination using dry film resist (DFR) has emerged as a favorable option for such applications. In this paper, a unique application of temporary DFR to overcome deep Si trenches will be presented. The integration scheme offers novel possibilities for wafer singulation in addition to resolving the issues with conventional spin-coating. An example of this approach will be presented in detail. This unique integration flow can lead to new applications that would otherwise not be feasible in technological areas such as sensor, microfluidics and MEMS.