18 June 2018 in Journal of Vibration and Acoustics
Although the vibration suppression effects of precisely adjusted dynamic vibration absorbers (DVAs) are well known, multimass DVAs have recently been studied with the aim of further improving their performance and avoiding performance deterioration due to changes in their system parameters. One of the present authors has previously reported a solution that provides the optimal tuning and damping conditions of the double-mass DVA and has demonstrated that it achieves better performance than the conventional single-mass DVA. The evaluation index of the performance used in that study was the minimization of the compliance transfer function. This evaluation function has the objective of minimizing the absolute displacement response of the primary system. However, it is important to suppress the absolute velocity response of the primary system to reduce the noise generated by the machine or structure. Therefore, in the present study, the optimal solutions for DVAs were obtained by minimizing the mobility transfer function rather than the compliance transfer function. As in previous investigations, three optimization criteria were tested: the H∞ optimization, H2 optimization, and stability maximization criteria. In this study, an exact algebraic solution to the H∞ optimization of the series-type double-mass DVA was successfully derived. In addition, it was demonstrated that the optimal solution obtained by minimizing the mobility transfer function differs significantly at some points from that minimizing the compliance transfer function published in the previous report.
1 April 2022 in Journal of Magnetism and Magnetic Materials
6 May 2023 in Journal of Sound and Vibration
13 June 2024 in IEEE Transactions on Magnetics
This paper presents a novel modeling method for a magnetostrictive energy harvester connected to a resonant circuit. The method is based on analytical calculations coupled with experimental parameter identifications. The magnetic flux leakages from the pickup coil and the magnetostrictive material are considered. Under the assumptions of linearity and fundamental oscillation, the governing equations of the magnetostrictive energy harvester were derived from the Euler-Lagrange equations for an electromagnetic-mechanically coupled system. The energy harvesting efficiency of the harvester was obtained by solving the derived governing equations, and it can be described with five non-dimensional parameters. Among the non-dimensional parameters, the natural frequency ratio and damping ratio of the load resistance have optimal values to maximize the energy harvesting efficiency. This study derived these optimal design parameters depending on the circuit configuration and types of energy given to the harvester. In the magnetostrictive energy harvester with a series-resonant circuit subject to kinetic energy impact, these optimal design parameters can be obtained in simple algebraic forms. Experimental validations were conducted for the magnetostrictive energy harvester with a pure resistive circuit, with series- and parallel-resonant circuits, respectively to compare their energy harvesting efficiencies. While the pure resistive configuration can harvest 21 % of given mechanical energy, both series- and parallel-resonant configurations can harvest 23 %.
1 January 2020 in Mechanical Engineering Journal
In the optimization of dynamic vibration absorbers (DVAs), it is generally assumed that the damping force changes in proportion to the velocity of the object; this damping is called viscous damping. However, many DVAs used in practical applications are made of polymeric rubber materials having both restorative and damping effects. This polymer material is considered to show a hysteretic damping force that is proportional to the displacement rather than the velocity of the object. Despite the widespread use of such hysteretically damped DVAs, there are very few studies on their optimal design, and the design formula of the well-known general viscously damped DVA is presently used for the design of this type of DVA. This article reports the optimal solution of this hysteretically damped DVA. For generality, it is assumed that the primary system also has structural damping that can be treated as hysteretic damping. Three optimization criteria, namely the H∞ optimization, H2 optimization, and stability maximization criteria, were adopted for the optimization of the DVA. For the H∞ optimization and stability maximization criteria, exact algebraic solutions were successfully derived, and for the H2 criterion, simultaneous equations with six unknowns and their numerical solutions were obtained.
1 January 2019 in The Proceedings of Conference of Kansai Branch
In the viscous damping, the damping force varies in proportion to the velocity of the object, whereas in the hysteresis damping it is proportional to the displacement of the object. Many of the dynamic vibration absorbers that have been put to practical use are made of polymer rubber rather than metallic springs and oil dampers, but their damping characteristics need to be modeled by hysteresis damping instead of viscous damping. This article clarifies the optimal design condition of this hysteretic damping type dynamic vibration absorber by H2 optimization criterion.