Understanding the oxygen evolution reaction (OER) activity and stability of the NiFe-based materials is important for achieving low-cost and highly efficient electrocatalysts for practical water splitting. Here, we report the roles of Ni and Fe on the OER activity and stability of metallic NiFe and pure Ni thin films in alkaline media. Our results support that Ni(OH)2/NiOOH does not contribute to the OER directly, but it serves as an ideal host for Fe incorporation, which is essential for obtaining high OER activity. Furthermore, the availability of Fe in the electrolyte is found to be important and necessary for both NiFe and pure Ni thin films to maintain an enhanced OER performance, while the presence of Ni is detrimental to the OER kinetics. The impacts of Fe and Ni species present in KOH on the OER activity are consistent with the dissolution/re-deposition mechanism we proposed. Stability studies show that the OER activity will degrade under prolonged continuous operation. Satisfactory stability can, however, be achieved with intermittent OER operation, in which the electrocatalyst is cycled between degraded and recovered states. Accordingly, two important ranges, that is, the recovery range and the degradation range, are proposed. Compared to the intermittent OER operation, prolonged continuous OER operation (i.e., in the degradation range) generates a higher NiOOH content in the electrocatalyst, which is likely related to the OER deactivation. If the electrode works in the recovery range for a certain period, that is, at a sufficiently low reduction potential, where Ni3+ is reduced to Ni2+, the OER activity can be maintained and even improved if Fe is also present in the electrolyte.
The performance of five hole‐transporting layers (HTLs) is investigated in both single‐junction perovskite and Cu(In, Ga)Se2 (CIGSe)‐perovskite tandem solar cells: nickel oxide (NiOx,), copper‐doped nickel oxide (NiOx:Cu), NiOx+SAM, NiOx:Cu+SAM, and SAM, where SAM is the [2‐(3,‐6Dimethoxy‐9H‐carbazol‐9yl)ethyl]phosphonic acid (MeO‐2PACz) self‐assembled monolayer. The performance of the devices is correlated to the charge‐carrier dynamics at the HTL/perovskite interface and the limiting factors of these HTLs are analyzed by performing time‐resolved and absolute photoluminescence ((Tr)PL), transient surface photovoltage (tr‐SPV), and X‐ray/UV photoemission spectroscopy (XPS/UPS) measurements on indium tin oxide (ITO)/HTL/perovskite and CIGSe/HTL/perovskite stacks. A high quasi‐Fermi level splitting to open‐circuit (QFLS‐Voc) deficit is detected for the NiOx‐based devices, attributed to electron trapping and poor hole extraction at the NiOx‐perovskite interface and a low carrier effective lifetime in the bulk of the perovskite. Simultaneously, doping the NiOx with 2% Cu and passivating its surface with MeO‐2PACz suppresses the electron trapping, enhances the holes extraction, reduces the non‐radiative interfacial recombination, and improves the band alignment. Due to this superior interfacial charge‐carrier dynamics, NiOx:Cu+SAM is found to be the most suitable HTL for the monolithic CIGSe‐perovskite tandem devices, enabling a power‐conversion efficiency (PCE) of 23.4%, Voc of 1.72V, and a fill factor (FF) of 71%, while the remaining four HTLs suffer from prominent Voc and FF losses.
A two-step post-deposition treatment approach enables organic residue control in TiO 2 and improves the efficiency of a Sb 2 Se 3 /TiO 2 thin film solar cell.
7 November 2024 in ACS Applied Materials & Interfaces
Metal halide perovskite solar cells (PSCs) have gained significant attention in thin-film photovoltaic research for their high power conversion efficiency (PCE) and facile fabrication processes. This study presents the use of inkjet printing to fabricate thin films of combinatorial mixed formamidinium tin-lead perovskites and evaluates their layer quality and device performance. Our findings demonstrate that incorporating Pb up to 50% into FASnI3 films enhances lattice stability. The investigation focused on optimizing the composition ratio for improved photovoltaic performance with FASn0.5Pb0.5I3-based PSCs achieving the highest PCE of 10.26%. Additionally, these cells exhibited an absorption spectrum extending beyond 1000 nm, corresponding to a 1.25 eV bandgap. The results suggest that inkjet printing can effectively enhance the efficiency of tin-lead-based PSCs, supporting scalability in device manufacturing.