This study presents the severity detection of pitting faults on worm gearbox through the assessment of fault features extracted from the gearbox vibration data. Fault severity assessment on worm gearbox is conducted by the developed condition monitoring instrument with observing not only traditional but also multidisciplinary features. It is well known that the sliding motion between the worm gear and wheel gear causes difficulties about fault detection on worm gearboxes. Therefore, continuous monitoring and observation of different types of fault features are very important, especially for worm gearboxes. Therefore, in this study, time-domain statistics, the features of evaluated vibration analysis method and Poincaré plot are examined for fault severity detection on worm gearbox. The most reliable features for fault detection on worm gearbox are determined via the parallel coordinate plot. The abnormality detection during worm gearbox operation with the developed system is performed successfully by means of a decision tree.
23 November 2020 in Journal of Vibration and Control
This study deals with the vibration reduction of a cantilever beam using air-jet thruster actuators controlled by the particle swarm optimized quasi bang–bang controller. In this study, the finite element model of a cantilever beam with the lumped mass of actuators is formed for the numerical simulations. Furthermore, the first-order plus dead time transfer function of the air-jet thruster actuator is found between the inlet pressure and the thrust. The quasi bang–bang control is proposed to suppress vibrations on the beam with impulsive air-jet pulses. The optimal location of the actuators and control parameters are determined with parametric study and particle swarm optimization, respectively. The performance of the control method is measured with the experiments of initial displacement, the presence of tip masses, and external disturbances. According to all results obtained in this study, it has been observed that the air-jet pulses successfully and rapidly attenuate vibration on the cantilever beam with the quasi bang–bang controller.
30 June 2019 in Journal of Measurements in Engineering
Especially, with the advancement of technology, mechanical parts need to be designed to be lighter and more durable. In the industry, gears are the most common power transmission equipment, and for this equipment, increasing durability and rigidity has an essential importance. During power transmission, undesired vibration and noise arise in gear systems. In addition to gear design, gearbox housing design is also essential to reduce the radiation of undesired structure-borne noise and vibration. In order to reduce noise and vibration levels, some modifications are frequently used on gearbox housings. In this study, three different gearbox housing designs (basic, cross and cellular) are formed and analysed by using ANSYS® software. The design alternatives for housings have been formed inside of the structure as different quantities of longitudinal and transverse stiffeners. In addition, all the external dimensions and the mass of these three housing designs are equal in order to observe just vibration and noise reduction. Fast Fourier Transform (FFT), statistical properties of vibration signals and sound levels of the gearbox have used for comparisons to determine which gearbox have better vibration and sound levels.
27 September 2023 in Dokuz Eylül Üniversitesi Mühendislik Fakültesi Fen ve Mühendislik Dergisi
It is possible to see convergent conical type nozzles everywhere, from daily life to rocket science. They are utilized as the main part of the propulsion system in many applications such as air blow guns for spraying, steam turbines for compression, rockets for thrust generation, satellites for altitude control and so on. Although the convergent conical nozzle is a well-known nozzle, there are few studies on the effects of geometric changes by comparing more than one approach together. Therefore, this study investigates thrust and volumetric flow rate for different inlet and exit diameters of the convergent conical nozzles theoretically, numerically and experimentally. In this study, the quasi-one-dimensional Euler equations are defined for the theoretical investigation of convergent conical nozzles. However, in this approach, many important features such as viscous losses are neglected. In fact, nozzle flows have highly complex features including shock waves, turbulence, and boundary layers due to compressible effects. Thus, Computational Fluid Dynamic (CFD) simulations are performed with ANSYS Fluent for numerical investigation of the nozzle in this study. CFD simulations provide a better understanding and illustration of convergent conical type nozzle flows. For a third approach, the experimental investigation is conducted for thrust and volumetric flow rate measurements. Theoretical and numerical results are compared with the experimental results and similarity ratios are defined to find the closest to the experimental results.