Mustafa Cigdem

Mustafa Cigdem

Auto-generated profile, based on publicly available information

Mustafa Cigdem

Yildiz Technical University

Research Focus & Metrics

Academic Career Length

36Years (1991-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2010 in Materials & Design (1980-2015)
Verified
Journal Article
Closed access
Fatih ToptanFatih Toptan
Fatih Toptan
AKAyfer Kilicarslan
Ayfer Kilicarslan
AKAhmet Karaaslan
Ahmet Karaaslan
MCMustafa Cigdem
Mustafa Cigdem
IKIsil Kerti
Isil Kerti


11 May 2005 in Scandinavian Journal of Metallurgy
Verified
Journal Article
Closed access
PDF file
AHA. Binnaz Yoruç Hazar
A. Binnaz Yoruç Hazar
MSMuhlis Nezihi Saridede
Muhlis Nezihi Saridede
MÇMustafa Çiğdem
Mustafa Çiğdem

1 September 2016 in Archives of Foundry Engineering
Verified
Journal Article
Open access
PDF file
CYC. Yuksel
C. Yuksel
OTO. Tamer
O. Tamer
EEEray Erzi
Eray Erzi
UAU. Aybarc
U. Aybarc
ECE. Cubuklusu
E. Cubuklusu
DDDerya Dispinar
Derya Dispinar
A356 is one of the widely used aluminium casting alloy that has been used in both sand and die casting processes. Large amounts of scrap metal can be generated from the runner systems and feeders. In addition, chips are generated in the machined parts. The surface area with regard to weight of chips is so high that it makes these scraps difficult to melt. Although there are several techniques evolved to remedy this problem, yet the problem lies in the quality of the recycled raw material. Since recycling of these scrap is quite important due to the advantages like energy saving and cost reduction in the final product, in this work, the recycling efficiency and casting quality were investigated. Three types of charges were prepared for casting: %100 primary ingot, %100 scrap aluminium and fifty-fifty scrap aluminium and primary ingot mixture were used. Melt quality was determined by calculating bifilm index by using reduced pressure test. Tensile test samples were produced by casting both from sand and die moulds. Relationship between bifilm index and tensile strength were determined as an indication of correlation of melt quality. It was found that untreated chips decrease the casting quality significantly. Therefore, prior to charging the chips into the furnace for melting, a series of cleaning processes has to be used in order to achieve good quality products.

9 February 2019
Verified
Book Chapter
Closed access
PDF file
ÇYÇağlar Yüksel
Çağlar Yüksel
UAUğur Aybarc
Uğur Aybarc
EEEray Erzi
Eray Erzi
DDDerya Dispinar
Derya Dispinar
MCMustafa Cigdem
Mustafa Cigdem

1 September 2011 in Materials Testing
Verified
Journal Article
Closed access
KGKerem Altug Guler
Kerem Altug Guler
MCMustafa Cigdem
Mustafa Cigdem
In this study surface finish and dimensional charactersitics of castings produced with gypsum bonded block investment moulds were investigated. Commercial and laboratory made gypsum bonded investment moulds were used for investment casting mould making. To compare the casting quality of the investment powders, wax patterns for surface roughness specimens and linear dimension measurement specimens were designed and produced with special geometry. Wax trees were assembled with these patterns, cylindrical stainless steel perforated flasks were settled around the trees and gypsum bonded investment slurries were filled into flasks. Conventional tin bronze and sterling silver were subsequently cast into these moulds by vacuum assisted and vacuum pressure casting processes, respectively. Afterwards, surface roughness of specimens were measured and linear dimensions of wax patterns and cast specimens were compared to determine percentage of dimensional change.