15 February 2021 in IEEE Access
Light-emitting Diode (LED) lamps have been widely used due to versatility and energy efficiency. However, LEDs are nonlinear loads, the massive usage will inject harmonics into the lighting system, which has influenced the power quality. Total Harmonic Distortion (THD) is an important parameter to evaluate the power quality, but the prediction of THD for LEDs is a challenging task. This paper addresses this issue by designing harmonic characteristics detection experiment and using artificial intelligence algorithm. Firstly, LED lamps with different driving circuits were tested, the relevant data of each harmonic were sampled and analyzed. Then, a THD prediction method based on an improved AdaBoost algorithm is proposed. In this method, a Generalized Regression Neural Network (GRNN) model is established, and its parameters are optimized by Mind Evolution Algorithm (MEA) to improve the search ability of GRNN. On this basis, the AdaBoost algorithm is utilized to integrate multiple MEA-GRNN individuals to form a strong predictor, which improves the generalization ability of the model. To avoid the integration failure caused by improper selection of threshold value, a sigmoid adaptive factor is added to improve the accuracy of AdaBoost algorithm. Finally, the Ada-MEA-GRNN model is trained and simulated with the LED harmonic data collected by the experiment. The simulation results show that the prediction accuracy of the proposed method is better than BP and GRNN, which can reach 95.48%. Meanwhile, even if the input dimension is reduced, the error is still small.
30 January 2023 in IEEE Transactions on Instrumentation and Measurement
Low-voltage circuit breakers (LVCBs) fault diagnosis based on artificial intelligence (AI) algorithm has always been a research hotspot and got some recent advances. However, AI algorithms usually require sufficient data to train the model, so intelligent fault diagnosis is a challenging task when lack of fault signals. To solve this problem, a fault vibration signal augmentation method based on Wasserstein distance and conditional generative adversarial networks (CGANs) is proposed in this paper. The proposed method uses Wasserstein distance to optimize the adversarial training of generator and discriminator, thus the generator can generate vibration signals under different fault conditions, which can be used to extend the training dataset. In order to verify the improvement effect of this method on the accuracy of LVCB fault diagnosis. Multiple fault classifiers are trained using generated and real fault signals, and a multi-dimensional evaluation index system is built to evaluate the classification effect. Experimental results reveal that the method can generate fault signals with high similarity and improve the accuracy of fault diagnosis.
6 August 2021 in IEEE Access
Nowadays, light emitting diode (LED) lamps have been widely utilized for lighting system due to its low-energy consumption. The harmonic emission standard is ignored by most of the manufacturers, high harmonic current will increase harmonic injection and cause fire risk. Existing research focuses on investigating harmonic emissions from several specific LED drivers, but a systematic evaluation approach is not given. The contribution of this paper proposed a LED harmonic evaluation in the management view, which can evaluate the harmonics of the LED lamps, accelerate the elimination of inferior LED lamps, and improve the power quality of distribution network. The evaluation approach combines G1 method and entropy method, which can make the weighting more scientific and rational. An evaluation model is established by collecting data, then the G1-entropy method is used to calculate the weights of harmonic characteristics in this model. Finally, we analyze and discuss the results, a specific evaluation approach is proposed, which can thoroughly and accurately represent the harmonic characteristics of LED lamps.
9 February 2024 in IEEE Transactions on Transportation Electrification
In urban rail traction power supply systems, the regenerative energy generated during train braking holds significant potential for energy conservation. By Integrating spatial-level analysis of power flow calculations from the electrical discipline with temporal-level optimization of train operation strategies from the transportation discipline, the utilization of regenerative energy can be further enhanced. Consequently, this paper presents an online energy optimization method for flexible traction power supply system based on spatiotemporal matching of train power. Firstly, the energy distribution and the power matching foundation are analyzed. Subsequently, a train power matching method is devised to provide a basis for train’s decision-making at any given time and location. Furthermore, the decision-making progress for train power matching is outlined to achieve online decision-making aimed at minimizing system incoming consumption. Finally, several simulations are performed to verify the effectiveness of the proposed method. In comparison to existing strategies, the online energy optimization method based on spatiotemporal matching of train power demonstrates a reduction in incoming consumption of 3.82% under variable load conditions, which holds value for practical applications.
4 December 2023 in IEEE Transactions on Transportation Electrification
Hot-spot temperature (HST) serves as a crucial indicator for condition monitoring and insulation evaluation of traction transformers. However, direct measurement of the HST in traction transformers is difficult, and in urban rail transit, where frequent load fluctuations pose challenges in accurately and efficiently calculating the HST. To solve this problem, this paper proposes an HST calculation method of traction transformer by combining a multi-physical model with a combined neural network. The multi-physical model is employed to obtain a large amount of HST data by performing Computational Fluid Dynamics (CFD) simulation. These simulation data are integrated into real-world operation data as the data set for neural network training. By calculating the winding temperature and HST separately, the combined neural network effectively addresses the issue of reduced accuracy in HST calculations caused by load fluctuations. Moreover, the superiority of the method is verified by comparing with other methods. It is demonstrated that the proposed method has higher accuracy than single neural networks and faster computational speed than the CFD-based method. It can be one of the online HST calculation solutions and without adding additional sensors, which has a great potential for engineering applications.