1 September 2024 in Physics of Fluids
An investigation of the multi-cycle dynamics of underwater explosion bubbles near hybrid boundaries is conducted using the experimental method. The experiments are carried out within a square steel tank. The free surface and a freely hanging steel plate comprise the hybrid boundary condition. Bubbles are initially positioned at equal distances from the two boundaries to facilitate a comparison of the relative influence exerted by each boundary. High-speed photography and pressure sensors are utilized to document the dynamics of bubbles and pressures in the flow field. An examination of the bubble behavior is conducted through the analysis of experimental imagery, elucidating the formation of a cone-shaped cavity near the free surface and the subsequent complex distortion behavior of the bubble as it interacts with the wall during the rebound phase. The investigation concentrates on the migratory properties of bubbles across various regions, revealing a spectrum of trajectories due to the varying boundary and buoyancy effects: vertical descent, “L”-shaped trajectory, “U”-shaped trajectory, and diagonal upward trajectory. Unless very close to the free surface, the direction of bubble migration changes at the end of each cycle due to local fragmentation of the bubble surface. Finally, the discussion culminated in an analysis of bubble energy conversion, revealing that the complex bubble behavior near the free surface weakens bubble collapse, resulting in minimal impact on the surrounding fluid dynamics from bubble oscillation. In the region distant from the free surface, when the bubble oscillation is weakly affected by buoyancy and boundaries, the energy emitted by bubble oscillation peaks due to the nearly spherical collapse.
1 August 2023 in Physics of Fluids
The dynamics of an oscillating bubble near a liquid–liquid interface is a complex multiphase flow problem due to the highly nonlinear interaction, such as interface fragmentation and bubble tearing. When one of the liquid mediums is non-Newtonian, its constitution would significantly influence both the bubble motion and the interface evolution. In this study, a numerical model is established based on the Eulerian finite element method with the non-Newtonian fluid described by the Herschel–Bulkley model. The numerical model is validated by comparing with experimental results for a non-spherical pulsating bubble at a water–oil interface and the analytical solution for the laminar flow of non-Newtonian fluids in a circular tube. According to the simulation and analysis with different case parameters, our findings suggest that the non-Newtonian fluid forms a crater when squeezed by the bubble, and the downward jet can penetrate the bubble and further deepen the crater. As the distance parameter increases, the crater gradually disappears or even bulges. Furthermore, the yield shear stress can give non-Newtonian fluid plastic properties similar to a solid, effectively reducing the bubble's pulsation and jet load. Additionally, the flow behavior index n comes from the power-law model for non-Newtonian fluids and significantly impacts the jet's impact process. When n≤1, the crater is likelier to become funnel-shaped, whereas when n > 1, it is likelier to become bullet-head-shaped. In addition to enhancing the bubble's nonsphericity, the reduction in Reynolds number also weakens the crimp deformation of the interface. When the distance parameter is zero, the larger the buoyancy parameter and the less deformable the non-Newtonian fluid, the easier the bubble to split by the annular jet.
1 November 2023 in Physics of Fluids
Previous Smoothed Particle Hydrodynamics (SPH) study on water entry issues has primarily been conducted for the load analysis of impact phase rather than the cavity oscillation effect because the calculation and simulation of this complex physical process are more complicated and time consuming. In order to increase computational efficiency and accuracy, the multiphase δ+-SPH model is combined with Adaptive Particle Refinement technology to investigate the whole process of the wedge's water entry. The hydrodynamic phenomena in the stages before cavity closure for the four cases with different Froude numbers (Fn) are compared and analyzed. After the cavity is pinched off, the wedge exhibits kinematic oscillation. Our test shows that the adoption of sound speed has a significant influence on the oscillation period and peak value of closed cavities in weakly compressible SPH calculations. Then, a suitable sound speed adoption is selected to simulate the oscillatory phenomenon accurately. Comparing the pressure profile with the surface pressure and acceleration of the wedge at the same time, it can be concluded that the oscillation of the hydrodynamic load on the wedge is caused by the pressure oscillation in the closed cavity. Especially for the case of low Fn, the pressure peak on the wedge's surface in the oscillation stage is even greater than the pressure load in the impact stage. The peak pressure of closed cavity is positively correlated with Fn and negatively correlated with Euler number (Eu). Finally, by analyzing the influence of wedge width and impact velocity, it is found that the oscillation period of the closed cavity is related to the morphology of the cavity. The larger the aspect ratio of the closed cavity, the longer the oscillation period.
30 June 2025 in Journal of Fluid Mechanics
Cavitation bubble pulsation and liquid jet loads are the main causes of hydraulic machinery erosion. Methods to weaken the load influences have always been hot topics of related research. In this work, a method of attaching a viscous layer to a rigid wall is investigated in order to reduce cavitation pulsations and liquid jet loads, using both numerical simulations and experiments. A multiphase flow model incorporating viscous effects has been developed using the Eulerian finite element method (EFEM), and experimental methods of a laser-induced bubble near the viscous layer attached on a rigid wall have been carefully designed. The effects of the initial bubble–wall distance, the thickness of the viscous layer, and the viscosity on bubble pulsation, migration and wall pressure load are investigated. The results show that the bubble migration distance, the normalised thickness of the oil layer and the wall load generally decrease with the initial bubble–wall distance or the oil-layer parameters. Quantitative analysis reveals that when the initial bubble–wall distance remains unchanged, there exists a demarcation line for the comparison of the bubble period and the reference period (the bubble period without viscous layer under the same initial bubble–wall distance), and a logarithmic relationship is observed that $\delta \propto \log_{10} \mu ^*$ , where $\delta =h/R_{max}$ is the thickness of the viscous layer h normalised by the maximum bubble radius $R_{max}$ , $\mu ^* = \mu /({R_{max }}\sqrt {{\rho }{{\mathop {P}\nolimits } _{{atm}}}})$ is the dynamic viscosity $\mu$ normalised by water density $ \rho $ and atmospheric pressure $P_{atm}$ . The results of this paper can provide technical support for related studies of hydraulic cavitation erosion.
1 September 2025 in Defence Technology
19 May 2025 in International Journal of Impact Engineering