19 August 2019 in Industrial & Engineering Chemistry Research
The role of choline chloride in biomass delignification by the deep eutectic solvent (DES) containing lactic acid was investigated. In this study, the influence of choline chloride on the pulping of Eucalyptus globulus chips was determined. Pulping experiments were performed at 120 °C for 8 hours with a DES to wood ratio of 20:1. Various experiments were performed to study the influence of choline chloride on lignin solubility, cleaving reactions and mass transfer in order to gain understanding of the observed pulping results. It was found that the chloride anion is the active component of choline chloride. In fact, the inexpensive salt NaCl performed as well as choline chloride in that respect. Furthermore, choline chloride it is already effective in a 1:250 molar ratio to lactic acid. It was found by studies on milled wood lignin (MWL) that choline chloride increases the cleavage rate of β-O-4, and thereby increases the delignification rate of biomass. Furthermore, choline chloride slightly decreased the solubility of lignin in DES and due to an increase in viscosity decreased the estimated mass transfer coefficient. Overall, the delignification rate of eucalyptus by lactic acid increased by the addition of halide salts.
1 December 2014 in Bioresource Technology
1 June 2013 in Current Opinion in Biotechnology
5 December 2022 in Waste Management
The predictability of pyrolysis yields and product composition of mixed plastics has been studied. To do so, pyrolysis of virgin polymers (HDPE, LDPE, PP, PS and PET) and eight individual sorting categories from a real waste DKR-350 stream (PE rigid/film, PP rigid/film, PET, PS, multilayer flexibles, and clogged materials) was performed in a batch reactor at 500 °C at laboratory scale. The obtained oil/wax, gas, and solid yields and the composition of oil/wax of those individual feedstocks were used as input of a superposition model to predict the corresponding pyrolysis yields and oil/wax composition of mixed feeds, which were later compared with the experimentally measured product yields from the pyrolysis of those mixed streams. This linear model predicts the oil/wax yield of the mixed streams to a reasonable extent, with a maximum yield deviation (overestimation) of 8 percentage points. However, the presence of significant amounts of PET (above 33 wt%) in the mixed plastic streams negatively impacts the production of the condensable product and promotes the formation of solid products beyond the expected predicted values. Quantification of the type of carbon (aliphatic, aromatic and carbonyl) present in all the oil/wax products was done using 13C NMR spectroscopy. A linear model could also predict the aliphatic carbon yield in the condensable product from plastic waste streams with high accuracy (maximum yield difference of 6 percentage points). However, the aromatic carbon yield could not be predicted, probably due to the observed behavior of PET, which interacts with other polymers to promote solid product formation.
20 February 2024 in ChemSusChem
This perspective combines various expertise to develop and analyse the concept of technology cascade for recycling waste plastics with the goal of displacing as much fossil crude oil as possible. It thereby presents archetype recycling technologies with their strengths and weaknesses. It then combines them in various cascades to process a representative plastic mix, and determines how much (fossil) naphtha could be displaced and at which energy consumption. The cascades rely on a limited number of parameters that are fully reported in supplementary information and that were used in a simple and transparent spreadsheet model. The calculated results bust several common myths in plastic recycling, e. g. by prioritizing here recycled volume over recycling efficiency, and prioritizing circular industry over circular products . It unravels the energy cost of solvent‐based recycling processes, shows the key role of gasification and the possibility to displace up to 70 % of the fossil feedstock with recycled carbon, a recycling rate that compares well with that aluminium, steel or paper. It suggests that deeper naphtha displacement would require exorbitant amount of energy. It therefore argues for the need to complement recycling with the use of renewable carbon, e. g. based on biomass, to fully defossilise the plastic industry.
15 September 2016 in Reaction Chemistry & Engineering
The interplay of chemistry, heat and mass transfer at particle and reactor levels was studied for the fast pyrolysis of cellulose.