Alvaro Javier Ortega

Alvaro Javier Ortega

Auto-generated profile, based on publicly available information

Alvaro Javier Ortega

Institute of Science and Technology Sidia Manaus Brazil

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 October 2020
Verified
Conference Paper
Closed access
JBJuliano Joao Bazzo
Juliano Joao Bazzo
RPRayner de Melo Pires
Rayner de Melo Pires
AOAlvaro Javier Ortega
Alvaro Javier Ortega
Navid SalehiNavid Salehi
Navid Salehi
PSPaulo Thiago Marreiros Santos
Paulo Thiago Marreiros Santos
Carrier Aggregation (CA) is one of the main features of LTE-Advanced that improves data rates by allowing the User Equipment (UE) to receive data on more than one Component Carrier (CC). The CA framework was used as the basis for other important 3GPP features like LAA (Licensed Assisted Access) and EN-DC (E-UTRAN New Radio NR – Dual Connectivity). This paper presents some real current measurements of a recently launched smartphone in intra and inter-band CA combinations up to 3 CCs. The experimental results show that 2 CCs of 10+10 MHz consumes 15% more energy during transmission than a scenario without CA with the same bandwidth. The energy consumption for inter and intra-band scenarios remains almost the same. It is higher for 3 than 2 CCs in about 7%. Measurements presented on this paper differ in 61% in some scenarios when compared with a work from 2012 and a device 6 generations older.

2 November 2021 in IET Communications
Verified
Journal Article
Open access
PDF file
AOAlvaro Javier Ortega
Alvaro Javier Ortega
Communications using the millimeter wave (mmWave) spectrum are a mainstream technology of the next generation systems due to their huge available bandwidth. However, the mmWave band will experience much more propagation loss than a low‐frequency band. Conventional precoding techniques are impractical in mmWave scenarios due to manufacturing costs and power consumption. Hybrid alternatives have been considered as a promising technology to provide a compromise between hardware complexity and system performance by reducing the number of radio‐frequency (RF) chains. In this paper, a hybrid processing design for downlink in mmWave scenarios is proposed, where the number of RF chains is reduced to the number of data streams. The precodification process is made by a three‐stage‐based hybrid precoder, whereas in the terminals, the equalization process only requires a low complex analog combiner. The three stages of the hybrid precoder are designed by a hierarchical strategy. The first stage addresses the phase shifters aiming to maximize the sum‐rate system, whereas the second and third stages are dedicated to mitigating the inter‐user interference effects. The proposed methodology gets a robust signal processing that can greatly mitigate the side effects of hardware reduction. Numerical results in terms of bit error rate (BER) and sum‐rate evidence that the proposed method not only overcomes other hybrid precoders/combiners but also reaches the same performance as a fully digital technique in some scenarios.

1 August 2020 in IET Communications
Verified
Journal Article
Open access
PDF file
AOAlvaro Javier Ortega
Alvaro Javier Ortega
RSRaimundo Sampaio‐Neto
Raimundo Sampaio‐Neto
RDRodrigo Pereira David
Rodrigo Pereira David
Millimetre‐wave (mmWave) communications have been regarded as a key technology for the next‐generation cellular systems since the huge available bandwidth can potentially provide the rates of multiple gigabits per second. Conventional precoding and combining techniques are impractical at mmWave scenarios due to manufacturing costs and power consumption. Hybrid alternatives have been considered as a promising technology to provide a compromise between hardware complexity and system performance. This study examines, using a semi‐analytic approach, the downlink performance of massive MU‐MIMO mmWave systems in terms of the bit error rate (BER). Also, a general expression is derived to estimate an upper bound/approximation to the BER performance via the Monte Carlo method, which can be used for any hybrid precoder/combiner, modulation and different data detectors. Numerical results evidence that the approximate BER expressions provide values very close to the ones obtained through simulation using only two statistical moments related to parameters of the system, mean and variance.