Deposition of perovskite films by antisolvent engineering is a highly common method employed in perovskite photovoltaics research. Herein, we report on a general method that allows for the fabrication of highly efficient perovskite solar cells by any antisolvent via manipulation of the antisolvent application rate. Through detailed structural, compositional, and microstructural characterization of perovskite layers fabricated by 14 different antisolvents, we identify two key factors that influence the quality of the perovskite layer: the solubility of the organic precursors in the antisolvent and its miscibility with the host solvent(s) of the perovskite precursor solution, which combine to produce rate-dependent behavior during the antisolvent application step. Leveraging this, we produce devices with power conversion efficiencies (PCEs) that exceed 21% using a wide range of antisolvents. Moreover, we demonstrate that employing the optimal antisolvent application procedure allows for highly efficient solar cells to be fabricated from a broad range of precursor stoichiometries.
5 February 2019 in Journal of Materials Chemistry C
This work investigates the effect of energetically shallow and deep surface defects in MAPbI3 films on the evolution of their photoluminescence properties upon exposure to ambient environment.
Vibrational control (VC) of photochemistry through the optical stimulation of structural dynamics is a nascent concept only recently demonstrated for model molecules in solution. Extending VC to state-of-the-art materials may lead to new applications and improved performance for optoelectronic devices. Metal halide perovskites are promising targets for VC due to their mechanical softness and the rich array of vibrational motions of both their inorganic and organic sublattices. Here, we demonstrate the ultrafast VC of FAPbBr3 perovskite solar cells via intramolecular vibrations of the formamidinium cation using spectroscopic techniques based on vibrationally promoted electronic resonance. The observed short (~300 fs) time window of VC highlights the fast dynamics of coupling between the cation and inorganic sublattice. First-principles modelling reveals that this coupling is mediated by hydrogen bonds that modulate both lead halide lattice and electronic states. Cation dynamics modulating this coupling may suppress non-radiative recombination in perovskites, leading to photovoltaics with reduced voltage losses.
Polymorphism in organic charge-transfer complexes induces a variation in electronic structure and sub-gap states which directly impact device physics. Single crystals are highly ordered, allowing for the measurement with reduced extrinsic factors.
Organic semiconductors are highly susceptible to defect formation, leading to electronic states in the gap—traps—which typically reduce the performance and stability of devices. To study these effects, we tuned the degree of charge trapping in organic thin-film transistors by modifying the film deposition procedures and device structure. The resulting charge carrier mobility varied between 10−3 and 10 cm2/V s in 2,8-difluoro-5,11-bis(triethylsilylethynyl)anthradithiophene. We analyzed the data using a Poole-Frenkel-like model and found a strong dependence of mobility on the field in low-mobility transistors and a field-independent mobility in high-performance devices. We confirmed the presence of traps in all films investigated in this study and concluded that the Poole-Frenkel model is not sufficiently sensitive to identify traps when their concentration is below the detection limit.
11 February 2022 in Journal of Materials Chemistry A
The use of antisolvents during the fabrication of solution-processed lead halide perovskite layers is increasingly common. Usually, the antisolvent is applied by pipetting during the spin-coating process, which often irreversibly alters the composition of the perovskite layer, resulting in the formation of PbI2 at the surface and bulk of the perovskite layer. Here, we demonstrate that by applying the antisolvent via carrier-gas free spraying, the stoichiometry of the perovskite layer is far better preserved. Consequently, the photovoltaic performance of triple cation photovoltaic devices fabricated in an inverted architecture is enhanced, mainly due to an increase in the open-circuit voltage. By exploring different volumes of antisolvent, we show that spraying as little as 60 μL results in devices with power conversion efficiencies as high as 21%. Moreover, solar cells with sprayed antisolvent are more stable than those fabricated by pipetting the antisolvent.