24 April 2015 in IEEE Transactions on Plasma Science
Railguns can reach higher muzzle velocities and fire rates than conventional guns. Muzzle velocities up to 2400 m/s and fire rates of more than 50 Hz have already been demonstrated with projectiles having a mass of 140 g and a square caliber of 25 mm. We investigated if a close-in weapon system (CIWS) based on a railgun performs better against incoming antiship missiles than a conventional CIWS such as the goalkeeper and propose solutions to optimize the performance of such a railgun. CIWSs are operational systems that defend a ship against incoming subsonic antiship missiles. However, the future antiship missiles will be supersonic and more difficult to defeat with conventional gun systems. Railguns are expected to perform better against these future threats thanks to their higher muzzle velocity and fire rate. Furthermore, the muzzle velocity within a single burst can be varied easily from shot to shot, generating a so-called intelligent burst. It allows varying the velocity of each projectile such that all projectiles arrive on the target at the same time. The number of projectiles, and thus the electrical energy required to achieve a target kill with an intelligent burst is expected to be lower than for railguns firing at constant muzzle velocity. In the first part, the performance of an electromagnetic CIWS is discussed using simulation models calculating the hit probability of a burst of projectiles fired with muzzle velocities ranging from 1200 to 2400 m/s and fire rates ranging from 75 to 300 rounds/s. The geometry of the target is that of a typical antiship missile, its velocity ranges from subsonic (300 m/s) to supersonic (600 m/s). The influence of the projectile mass on the performance of the system and the required electric energy was also investigated. We confirmed that the concept of intelligent burst reduces the required electric energy, especially against supersonic targets. The second part deals with some technical aspects of high fire rate railguns. We have shown experimentally that an automatic loading system allows increasing the fire rate of a medium caliber railgun from 50 to 75 Hz.
1 June 2017 in IEEE Transactions on Plasma Science
The most important part of a railgun launch package is the armature where the electromagnetic force is generated leading to the acceleration of the launch package. In case of metal armatures, the most commonly used armature types are the C-shape and the multifiber brush technology. However, rarely both armature types were systematically compared under similar experimental conditions. That is why we constructed launch packages based on the C-shaped and brush armature technology with comparable armature and payload mass. With these launch packages, a series of experiments was performed in an energy range between 0.8 MJ and 1.13 MJ corresponding to a speed range between 950 m/s and 1400 m/s. The results of the experiments were then analyzed qualitatively and quantitatively. On the one hand, our results showed that the total losses are higher for the C-shaped armature technology than for the brush armature technology. On the other hand, our results showed that launch packages based on the C-shaped technology convert better electrical energy into kinetic energy.
7 June 2019 in IEEE Transactions on Plasma Science
The rapid-fire railgun (RAFIRA) is a railgun, which can be operated in multishot mode. However, so far, the number of shots in a multishot experiment was limited to two shots per experiment. That is why RAFIRA was adapted electrically and mechanically and multishot experiments with shots 2, 3, and 5 per experiment were performed. In these experiments, fire rates between 40 and 80 Hz and muzzle velocities up to 1700 m/s were achieved.
20 August 2019 in IEEE Transactions on Plasma Science
The knowledge of the current density distribution in C-shaped armatures during a railgun experiment can be of crucial importance in the understanding of transition mechanisms and optimization of the electrical contact between rails and armature. That is why we applied during single-shot experiments with C-shaped armatures the measurement technique described, in order to deduce the spatial and temporal current density distribution of C-shaped armatures during the experiment. Based on our experimental results, we observe nonuniform current density distributions in the armature, including areas with high current densities and very low current densities. We compare our findings with the state of the post shot rail surfaces and to strengthen our interpretation we performed 3-D simulations using the COMSOL Multiphysics program.