Mohammad Mohsin

Mohammad Mohsin

Auto-generated profile, based on publicly available information

Mohammad Mohsin

Mechanical Engineering Department, Jamia Millia Islamia, New Delhi, India

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2017 in Materials Research Express
Verified
Journal Article
Closed access
PDF file
SASajjad Arif
Sajjad Arif
MAMd Tanwir Alam
Md Tanwir Alam
AAAkhter H Ansari
Akhter H Ansari
MSM Arif Siddiqui
M Arif Siddiqui
MMMohammad Mohsin
Mohammad Mohsin

21 December 2023 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
ASAbdul Samad
Abdul Samad
SASajjad Arif
Sajjad Arif
SASalman Ansari
Salman Ansari
MMMuhammed Muaz
Muhammed Muaz
MMMohammad Mohsin
Mohammad Mohsin
WAWahid Ali
Wahid Ali

1 October 2017 in Materials Research Express
Verified
Journal Article
Closed access
PDF file
MMMohammad Mohsin
Mohammad Mohsin
AMAas Mohd
Aas Mohd
MSMohd Suhaib
Mohd Suhaib
SASajjad Arif
Sajjad Arif
MSMohammad Arif Siddiqui
Mohammad Arif Siddiqui
In this experimental work, aluminium Al-20Fe-5Cr (in wt. %) matrix reinforced with varying wt. % Al2O3 (0, 10, 20 and 30) and compaction pressure (470, 550 and 600 MPa) were prepared by powder metallurgy technique. The characterization of composites were performed by Scanning Electron Microscopy (SEM), X-ray diffraction (XRD), Energy Dispersive Spectrum (EDS) and Elemental Mapping. Uniform distribution of Al2O3 in aluminium matrix were observed by elemental mapping. The composites showed an increase in density and hardness by increasing both alumina and compaction pressure. While, electrical conductivity decreased by the addition of alumina. The tribological study of the composites were performed on pin-on-disc apparatus at sliding conditions (applied load 40 N, sliding speed 1.5 m/s, sliding distance 300m). The tribological properties of the composites were improved by increasing alumina and compaction pressure. SEM analysis were also carried out to understand wear mechanism of the worn surfaces of various fabricated composites and aluminium matrix.

2 January 2021 in Engineering Research Express
Verified
Journal Article
Closed access
PDF file
MMMohammad Mohsin
Mohammad Mohsin
MQMohammad Aatif Qazi
Mohammad Aatif Qazi
MSMohd. Suhaib
Mohd. Suhaib
MSMOHD BILAL NAIM SHAIKH
MOHD BILAL NAIM SHAIKH
MMMohd Misbah
Mohd Misbah

1 August 2017 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
MMMohammad Mohsin
Mohammad Mohsin
AMAas Mohd
Aas Mohd
MSM. Arif Siddiqui
M. Arif Siddiqui
MSMohd. Suhaib
Mohd. Suhaib
SASajjad Arif
Sajjad Arif
This work illustrates the results of the effect of aluminum oxide (Al2O3) on the green density, hardness and electrical conductivity of Al-Fe-Cr-Al2O3 powder composites at different compaction pressures (470 MPa, 550 MPa and 600 MPa). SEM analysis for different Al2O3 composition was done. The composite consisted of Al-75%, Fe-25%, Cr-5% by weight as matrix material and alumina (Al2O3) was added in varying percentage by weight (0-30), as reinforcement. Powders of Al, Fe, Cr and Al2O3 having average particle size of 48 µm, 150 µm, 100 µm and 100 µm respectively with all having purity ≥ 99% were used. Ethanol (5 wt. %) had been used as a process control agent (PCA). Synthesis of Al-Fe-Cr-Al2O3 composites was carried in shaker mill. The ball to powder ratio was kept 20:1. The characterization of the powder was followed by Scanning Electron Microscopy (SEM). There was an increase in green density, hardness and electrical conductivity with increase in compaction pressure but no significant effect of adding alumina on these properties was observed.

1 September 2021 in Engineering Research Express
Verified
Journal Article
Closed access
PDF file
MMMohammad Mohsin
Mohammad Mohsin
MQMohammad Aatif Qazi
Mohammad Aatif Qazi
MFMohammad Faizan
Mohammad Faizan
In the present research work predicted properties of Aluminium Alloy Composites prepared through powder metallurgy technique have been examined using Artificial Neural Network (ANN) approach. The aluminium alloy (Al-20Fe −5Cr) matrix reinforced with aluminium oxide (Al 2 O 3 ) varying from 0–30 wt% with a step of 10 wt% were prepared. The green compacts prepared at three different compaction pressures viz. 470, 550 and 600 MPa were sintered at 440 °C for 30 min. Pin-on-disc test was performed to evaluate wear loss of the composites prepared. The influence of alumina varying weight percentage and different compaction pressure had been analyzed and tests were performed according to full factorial design. Analysis of variance (ANOVA) had been employed to predict the percentage contribution of various process parameters. The results indicated that the wear loss was mainly influenced by alumina percentage followed by compaction pressure by 92% and 8% respectively. For modeling and prediction of wear loss, a feed forward back propagation neural network was constructed and compared with experimentally calculated values. Both experimental and ANN predicted values of wear loss were in close correlation with each other with approximately (1–3) % error.